squeeze bottle lids 3d models
109888 3d models found related to squeeze bottle lids.thingiverse
A little lid for cheap squeeze bottles. I'm using these to store two part silicone rubber for mess free dispensing. **WARNING:** Depending on your plastic AND nozzle material (brass may contain lead) it may or may not be safe to use 3d...
thingiverse
Customized version of http://www.thingiverse.com/thing:995222 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=995222 Instructions Using the following options: top_id...
thingiverse
This is a lid for a water or soda bottle that turns it into a squeeze bottle. Use it for condiments, sake, watering plants, whatever you want! I made it to replace the broken lid on a Costco sized bottle of lemon juice, which didn't originally have a...
thingiverse
A little lid for cheap squeeze bottles. Modified from cnt's design to remove the center post, which is too thick for some bottles. **WARNING:** Depending on your plastic AND nozzle material (brass may contain lead) it may or may not be safe to...
thingiverse
Designed so it doesn't need any supports (hence the slightly different geometry than the original on left) Inner Diam: 13/16" (20.6mm) Outer Diam: 15/16" (23.8mm) Thread pitch: 1/8" (3.2mm) Disclaimer: I haven't actually squeezed epoxy through this...
thingiverse
Customized version of https://www.thingiverse.com/thing:995222 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=995222
thingiverse
Customized version of https://www.thingiverse.com/thing:995222 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=995222
thingiverse
Customized version of https://www.thingiverse.com/thing:995222 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=995222
thingiverse
Customized version of http://www.thingiverse.com/thing:995222 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=995222 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:995222 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=995222
thingiverse
Customized version of http://www.thingiverse.com/thing:995222 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=995222 Instructions Using the following options: top_od...
thingiverse
You empty bottle keep them fill with juice and put the corresponding lid on and there is a kids training lid
cults3d
An organizer for squeeze bottles (30ml) for hobbies. ...keeps them upright and together for easy storage.
cgtrader
is squeeze bottle for medical and chemical use,created under blender 3D 2.93.0 rendered with PBR textures in eevee and cycles.
thingiverse
This is a holder/caddy to hold standard food-grade squeeze bottles rightside-up or upside-down. ... Tree supports are built into the model.
thingiverse
This bottle is filled is isopropanol alcohol to clean solder flux off my boards but it tips over ALL THE TIME. ... Problem solved. (In case you are wondering, this is a recycled Scalpicin squeeze bottle.)
thingiverse
Who struggles to get the last bit of ______(fill in the blank: glue, shampoo, etc) from a bottle? ... This holder maintains the squeeze bottle upside down to help the contents drain completely.
thingiverse
This is a simple holder for four (can be customized) Pico Squeeze 'squonk' bottles. It's designed to be used with the bottle caps designed by limafox https://www.thingiverse.com/thing:2543546. ... The object allows for easy customization and includes a...
thingiverse
Eleaf Pico Squeeze ecig bottle cap. You can store or carry around your preferred ejuices right into squonk bottles. It is designed to have minimum tolerance with 0.4mm extruder and 0.2mm layer height. ... It is possible that you'll have to slightly...
thingiverse
There was a cap attached to this squeeze bottle but it came off easily. So, I made one. I prefer the one with the rim but it didn't get printed very well because of the support I added (couldn't remove the support). I haven't tried yet but it might...
thingiverse
I use these Wilson Candy Making squeeze bottles for a lot of things around the shop (this one is for paint thinner), but the caps always seem to get lost or damaged -- and even when they're not lost or damaged, they're tiny and tapered, so they're...
thingiverse
... replace with the top print. It may take a bit of force to snap it in place but you only got to do it once as you can just twist it for the next bottle. ... Up to you if you wanna keep the little white gasket which may help it seal a bit better.
thingiverse
We bought a bunch of these isopropanol bottles for work, but they did not come with caps. I designed them for a snug fit to minimize accidental spills or evaporation. ...I added a loop for a tether like a cable tie or string to prevent the...
thingiverse
Squeeze bottle holder wall mounted , for 60 mm (250 ml)
thingiverse
This is a replacement cap for the Pico Squeeze bottle the holes allow 2x2mm magnets to fit easily (no need to glue here)
thingiverse
This is a holder for a set of IKEA grilltider and other squeeze bottles. The bottom where the bottle sits has a grill design to allow for condiments like spilled oil etc to stagnate without touching the base of the bottle too much. It does not drain...
cgtrader
Squeeze Bottle Tip 3D model Modeled in Blender. Preview image rendered using cycles. All scene are included in .blend files. All object have been named appropriately. ...Convert to:- - 3D studio - Collada - Wavefront ...