ssd adapter 3d models
118478 3d models found related to ssd adapter.thingiverse
This SSD adapter is used for the SSD slot of 'Blackmagicdesign SSD 4K' Video Recorder. It does not loose even when using 6.4mm SSD. It is a little tight, so please do the sandpaper after printing. 조금 빡빡할수 있으니 프린팅을 한후 사포작업을 해주세요. ...
thingiverse
This is an SSD drive adapter to mount in a standard 3.5" drive slot. Designed to work with dell clip in trays as seen in the photo above. It will fit any 3.5" hard drive tray that uses the standard side mount holes. ...
thingiverse
My son needed an SSD adapter for his computer. SSD drives don't vibrate so it doesn't take too much to secure one. This adapter lets you put the SSD in a standard bay. There is access to the SSD mount holes on the side, but it is much easier to...
thingiverse
SSD Adapter V1 to stop wiggle. Just a quick design to improve the stability of the SSD upon FFG's stands. Will need to adjust with needle files, unless you want permanent on SSD use silastic to secure to stand or SSD. Enjoy modify as heck and share...
prusaprinters
This is a small SSD mounting adapter for my Synology DS218+. ...Theoretically this should also work for other "slot"-type drive cages.Note that the latch is missing the little pin on the front.Original source for the adapter plate:...
thingiverse
DO NOT PRINT! ... NO VENTILATION!!!! Blackmagicdesign Hyperdeck 7mm SSD adapter
prusaprinters
Model This is an SSD adapter for the Atomos Ninja Flame, it allows you to use standard 2.5" SSD's. ...They slide in perfectly and snugly making it much easier to use. Print Settings Print this with any sturdy filament, supports are not needed but the...
thingiverse
Model This is an SSD adapter for the Atomos Ninja Flame, it allows you to use standard 2.5" SSD's. They slide in perfectly and snugly making it much easier to use. Print Settings Print this with any sturdy filament, supports are not needed but the...
thingiverse
An adapter plate for mounting an SSD in a Mac Pro hard drive docking bay. It uses split locking tabs to securely snap into the existing metal drive tray for fast and easy installation. ... Instructions...
thingiverse
... "Disk Tray D9" This is not perfect, but it´ll do the job. One of the fixing rails can not be inserted in the drive cage, the knob stands out to far and touch the SSD drive. Other than that it works. Feel free to remix or consider it crap. ...:-)
thingiverse
ODD to SSD adapter for HPE Proliant MicroServer Gen8 (https://support.hpe.com/hpsc/doc/public/display?docId=emr_na-c03793258)
cults3d
2.5" SSD disk adapter for 3.5" mounting Size 100mm by 17mm Increases your magnet by 86 if you print it in red.
thingiverse
This is an SSD adapter designed to fit into the 3.5" drive bay on (some) Dell PCs. It fits into the existing caddy as a push fit and is offset. The caddy requires the drive to be off-centre whereas other adapters I found were centred, which fouled...
cults3d
This is an SSD adapter designed to fit into the 3.5" drive bay on (some) Dell PCs. It fits into the existing caddy as a push fit and is offset. The caddy requires the drive to be off-centre whereas other adapters I found were centred, which fouled...
cults3d
Adapter to replace the hard drive with an SSD, has base and side holes, if you put the base screws just put two the closest to the sata connector. ... I corrected the hole shown in the photo that had to be moved.
cgtrader
Hard disk adapter 2.5 SSD to 3.5 HDD frame for installation in desktop PC Dimensions 3.5 "HDD frame Length: 145mm Width: 100mm Height: 20mm Dimensions 2.5 "SSD Length: 100mm Width: 70mm Height: 7mm
thingiverse
I just put a SSD disk into an older iMac A1311 for a customer - he had purchased the SSD without realising these older (2009-2011) imac's use a 3.5" drive, while all SSD's are, of course, the newer and much smaller 2.5". I tried a few 2..5" to 3.5"...
thingiverse
Adaptor for PS2 FAT SSD Tested on Samsung Evoline (860 QVO) SSD dimensions LxWxH 100mm 70mm 6mm PS FAT HDD-Space dimensions LxWxH 151mm x 106mm x 27mm Adaptor dimensions LxWxH 150,4mm x 105,34mm x 26,5mm Misc Enjoy
thingiverse
... instructions of ifixit. You'll also need two screws (I used M3x3,5 which were delivered with my SSD), to mount the SSD on the bracket. ... Instructions: https://www.ifixit.com/Guide/iMac+Intel+27-Inch+Retina+5K+Display+Hard+Drive+Replacement/30522
thingiverse
This allows a 3.5" hard drive to be replaced with a 2.5" SSD drive in Dell Optiplex tower and small form factor cases, models 9020, 9010, 755, 740, and other similar cases.