strip maker 3d models
59778 3d models found related to strip maker.pinshape
Toast Strip Maker: This design is a cool new way of eating toast! Once you print this file, you will be able to cut pieces of bread and then toast them and have strips of toast. When the bread is finished toasting, you will have a nice piece of...
thingiverse
Shortly after publishing, I had some ideas on how to resolve some design flaws that ended up with me making a v2, which can be found here: https://www.thingiverse.com/thing:4227671 This test strip maker will still work just fine if you want to print...
thingiverse
this is a tool to cut strips of plastic from a plastic bottle such as a coke bottles. i included a plastic blade but u may want to use a metal blade. lay the blade between the two blade holders and cover with the cover. you may have to clamp to a...
pinshape
Summarythis is a tool to cut strips of plastic from a plastic bottle such as a coke bottles. i included a plastic blade but u may want to use a metal blade. lay the blade between the two blade holders and cover with the cover. you may have to...
prusaprinters
this is a tool to cut strips of plastic from a plastic bottle such as a coke bottles. i included a plastic blade but u may want to use a metal blade. lay the blade between the two blade holders and cover with the cover. you may have to clamp to a...
thingiverse
... something that could do the same. This design is similar to some existing test strip makers I've seen, and is approximately 7.5" wide (to fit across an 8x10 easel area). ... It also has holes for magnets, sized around McMaster-Carr part 7048T22.
thingiverse
A localised test strip maker for darkroom photography. It is for 80x60mm test papers (18x24cm cut by thirds). But you can try to scale it during printing. If you print top white (to see image when positioning) then paint bottom side black to...
thingiverse
I just recently added the Z Brace mod (https://www.thingiverse.com/thing:921948) and wanted to change where my led light strip is. Created these long flat bars that snap onto the M8 threaded rod. ...
thingiverse
**Effective.** Consistently prints the exact same piece of image area onto each of 4 test strip sections, so you can make 1:1 comparisons between different exposures. 2. **Efficient.** Each test strip is 2.5 x 4", or 1/8 of a standard 8x10 sheet. ...
thingiverse
I printed one off, and wired up and installed 4 strips to show what it should look like when you build and mount the light strips to it. The plan is to make some LED Lightbars to mount on the ceiling of my garage to replace the aging Flourescent...
thingiverse
... ...The fit is snug enough to keep the parts in place without any glue or tape. The adhesive on my light strip wasn't very strong, so I made some clips to keep the strip in place. ...You may or may not need them depending on what light strip you get.
thingiverse
Remixed the original to fit the screw spacing on the Monoprice Maker Select V2.
thingiverse
I have a bunch of those Aliexpress DIN terminal "UK-2.5B" in my breaker box but I always missing some of those plastic markers. So I decided to print them! ... Hope this will be useful to many of you!
thingiverse
LED strip from right side all the way across and down to left, making sure that you get the strip all the way into the corner and make a sharp angle or the covers won't fit. Then attach the LED covers, 2x100mm and 1x80mm on the vertical sides,...
thingiverse
Print Settings Printer: Monoprice Maker Select Rafts: Doesn't Matter Supports: No Resolution: 0.2 Infill: 20 Notes: Print with the thing laying on its back, no supports needed. ...How I Designed This OpenSCAD OpenSCAD source is provided...
thingiverse
My spouse wanted a snap on 3M Command Strip holder that could be glued to anything. I loved the design of https://www.thingiverse.com/thing:3021743 and remixed the hook to instead be a large flat. I tried to keep as much of the original design as...
thingiverse
IMPORTANT: My replacement part does not extend down into the container that holds the ice-cream mixture on the machine I was repairing. You should check to be sure that it does not extend into the ice-cream mixture for your machine. Unless your PLA...
thingiverse
LED strip from right side all the way across and down to left, making sure that you get the strip all the way into the corner and make a sharp angle or the covers won't fit. Then attach the LED covers, 2x100mm and 1x80mm on the vertical sides,...
thingiverse
Changes - Seperated the components for printing with different infill and better use of print bed. The connectors and the fabric arm should have more infill to make them a bit stronger- I printed them at 50% infill 0.15 layer height in ...
thingiverse
... ...I searched for a while, but was unable to find an LED strip holder that fit the i3 Plus so I made one. This should hold any standard width (~11mm) LED strip. ...There is no need to use adhesive as the strip should just slot in and be fairly secure.
thingiverse
This is another minor adjustment to change the screw hole distance to 3cm. ... Just moved the holes 5mm inward on each side, left the wire loop thing in place. length of led strip remains 5cm
thingiverse
See also my remix of LED strip holder to add LED strip to the gantry: http://www.thingiverse.com/thing:2064648 Full build: Wire (This is what I had, 20 or 22ga are more than adequate):...
thingiverse
These covers are remixed to make them connect to the holders correctly and so that they sit flush against them.
thingiverse
Simple mask to use for prints. ...Better with higher infill to make it a bit heavy. Print five "doors" to use it as test strip maker, glue handle on top.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=678211 Instructions Using the following options: textstring = Maker text_excenter_factor = 1 fontname = Telex RoundBase = 1 textsize = 16 base_radius_add = 3 cutangle = 75 baseheight = 1...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=834725 Instructions Using the following options: Rotation = 55 Loop_font = Chewy Loop_x_position = 15 Text = Maker Loop_character = o center = 60 height = [5,6,4,5,4,3,3,4,5] Font_name = Chewy...