stylus holder 3d models
329244 3d models found related to stylus holder.cults3d
Stylus holder for touch screens. Diameter 9.2mm. ...For ABS - set 101-102% scale.
thingiverse
Stylus holder for touch screens. Diameter 9.2mm. ... For ABS - set 101-102% scale.
thingiverse
A simple stylus holder modeled to hold the TDI Bluetooth stylus that accompanies the miniature game Golem Arcana, styled to resemble the stylus.
thingiverse
This is a stylus holder for a stylus ( https://www.amazon.com/gp/product/B01J0RV64C/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1) I purchased for my yoga 3 910. This holder will fit any stylus that is less than 10mm. This can also hold a pen, pencil...
thingiverse
So as necessity is the mother of invention, I designed a double stylus holder that allows for one or two finger tapping. While I haven't tested it thoroughly on a boss monster, it's simple enough to fit one or two single centimeter stylus. ... such as...
cults3d
Adjustable clip on tray for holding a stylus or other pen shaped computer accessory
sketchfab
Mascot-esque character stylus holder developed for test printing and personal fulfilment.
thingiverse
I couldn't resist designing Mjolnir stylus holder and then sculpted some rocks in Zbrush. The hole for the stylus is 13.8mm, based on a Huion stylus. It's a huge stylus holder, but why the heck not?? ...:))
thingiverse
A simple Wacom Bamboo stylus holder. Wondering if your stylus will fit? ...The hole is 11mm diameter.
cults3d
Laptop Stylus Holder Clips x2 varieties for different screens / tablets Print @ 0.16 - 0.20 No supports needed
thingiverse
Laptop Stylus Holder Clips x2 varieties for different screens / tablets Print @ 0.16 - 0.20 No supports needed
thingiverse
... minor cleaning of support material. Instructions Print the stylus holder. Remove the support material (with knife or fine needle-nose pliers). Insert stylus holder into tablet's stylus holder Stand your stylus vertically. ... ... Profit!
thingiverse
The Stylus holder that comes with the XP-Pen Table is a little unstable, so I made a little holder for it. ...
cults3d
Whipped together from other people's design. ...I wanted a stylus holder that fit my tastes. The holder can currently hold a stylus 10mm or smaller in diameter. ...The whole is about 18mm deep.
thingiverse
Whipped together from other people's design. ...I wanted a stylus holder that fit my tastes. The holder can currently hold a stylus 10mm or smaller in diameter. ...The whole is about 18mm deep.
thingiverse
Just a simple stylus holder for the Holley EFI touchscreens. Just simply Glue it on to something. ... Check out my replacement Stylus here- https://www.thingiverse.com/thing:4840249
thingiverse
Stylus holder for UGFPV or Flysky Nirvana Radio. ... Here is where you can buy the stylus: https://www.amazon.com/gp/product/B07FNKYGD1/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
thingiverse
This is a pen tablet stylus holder for your eyeglasses. ...In the slot for the frame, since my glasses dont have a thick arm I stuck some window insulation foam in there to keep it tight.
myminifactory
It is overkill for just a stylus holder, but being Mjolnir, that's completely justifyable :) The head and rocks can be glued together after printed, but it is a pretty tight fit
thingiverse
This is a Stylus Holder that clips to the door handle of a Robo R2 3D printer. I put in my own "support block" which you remove after printing just below the rounded clip. ... https://youtu.be/He9_z3UYWw4