tacoma phone mount 3d models

Simple fitted phone mount for 2016+ Toyota Tacoma.

I wanted a phone holder for my 1997-2004 Tacoma that would allow me to stick on the magnet that came with my phone case: https://smile.amazon.com/gp/product/B08G8CTXBS I also wanted it to replace the screw for the Oh Sh*t handle on the driver side,...

There are 4 different options to choose from: - Flat with Cable Management - Flat without Cable Management - 10 degree tilt with Cable Management - 10 degree tilt without Cable Management This is the phone magnet mount I used:...

I've been trying to find a good place to store my phone in my Tacoma. The cup holders are always in use and the charging pad area is usually full of stuff and isn't a convenient location. I remixed two ideas together to come up with this solution. It...

I used a Wizgear magnetic phone mount, removed the tape from the mount and used epoxy instead. I'm sure the tape could still be used instead of epoxy, I just wanted better heat resistance. The mount was designed around a 10-24 machine screw and nut...

Simple design to mount phone in tacoma 3rd gen. Just use 3m "extreme" double side tape to stick magnet mount linked below. The phone case I am using (linked below also) has metal infused into it so there is no need for the classic metal plates most...

I also superglued the 3mm nuts to the support plate, since you cant install the dash with the mounting plate installed.  Parts -2ea - M3 x 8mm bolts2ea - M3 nuts1ea - RAM Mounts Ball Adapter with 1/4" - 20" Female Threaded Hole and Hex Post...

I designed this to interface with a generic phone holder instead of using the mounting mechanism that came with it. I recommend printing this with PETG or ABS at a high infill and using multiple outer walls with the print. Also, please note that...

This is a 17mm ball mount designed to fit onto the center of the dashboard on a 3rd generation Toyota Tacoma, above- or next to the infotainment screen. It requires some double sided tape to install and is best printed in PETG or some other heat...

I used PRUSA FlexFill 98A. ...Any TPU should work

iPhone 12 pro max used in picture Used 3M Super-Strength Molding Tape, 03614, 1/2 in x 15 ft for sticking the mount to the car (might need to be modified for different adhesives) phone clamp from junkyard but probably can get one from amazon...

phone holder for 2018 toyota tacoma radio. ...hope you enjoy

plate to mount hopkins insight brake controller in a 3rd gen tacoma. ...replaces useless cubby on left of steering wheel.

Phone Holder for 2018 Toyota Tacoma (Fits in vents & on top dash) Printed in PETG for temp. ...resistance, parts all printed separately Phone charger hole in bottom of housing, chamfer on bottom face of both large parts for ez removal

...... I created this UV5R Radio mount for my 2010 Toyota Tacoma TRD Off-Road. I printed it face down without any issues. It is designed to be used with the belt clip provided with your radio. I added 3M automotive mounting tape to the back of the mount.

This is a simple dash mount I remixed to hold a backup camera screen for my RV, it would also work well as a phone mount with a magnet mount.

Wasn't able to find an elegant solution to mount the slim radios. ...The thicker android radios using the double din standard work fine with the OEM mounts with the tabs bent back, but this is for the slimmer radios as pictured.

I combined qwiktunes Echo Auto Mount Base with Cracked1's phone mount to make something that would work for a 2018 Tacoma. ... I've glued 2 8x3mm neodymium magnets into it and it works great so far.

I combined qwiktunes Echo Auto Mount Base with Cracked1's phone mount to make something that would work for a 2018 Tacoma. ... I've glued 2 8x3mm neodymium magnets into it and it works great so far.

A Toyota Tacoma dashboard bracket that fits the ball mount from a 5" camera display. It fits a 2022 but should work on any 3rd gen Tacoma. I printed in PETG but PLA might be strong enough, the bracket body is thick and sturdy. ...I added some small...

A Toyota Tacoma dashboard bracket that fits the ball mount from a 5" camera display. It fits a 2022 but should work on any 3rd gen Tacoma. I printed in PETG but PLA might be strong enough, the bracket body is thick and sturdy. ...I added some small...

Vled rear mount for 3rd gen toyota tacoma Print two, squares on top are for a zip tie to keep the cable down. I recommend ABS. (I did PLA, we shall see how long it lasts.) I still used the 3m for the light. I also used 3m for adhesion to the...

This is a 2 piece mount to put a magsafe charger in place of the airbag switch on a 95-04 Toyota Tacoma. Print the Magsafe piece laying down Print the dash clip piece on its side with supports. ...If you print it laying down the tabs will most...

An iPad mini mount for the front cupholder in a 3rd gen Toyota Tacoma. This replaces the OEM middle divider part. The bracket is sized to fit an iPad mini 4 in landscape. I might build a larger size for an iPad if there is enough space. ...If requested,...

An iPad mini mount for the front cupholder in a 3rd gen Toyota Tacoma. This replaces the OEM middle divider part. The bracket is sized to fit an iPad mini 4 in landscape. I might build a larger size for an iPad if there is enough space. ...If requested,...

Holds a scan gauge in late model 1st gen Tacoma ash tray location

I got tired of my phone not having a place in my Tacoma so I designed and have printed this a few times and I believe it's perfect for my application. ...it sits in the slot and has a slight angle to make it so the phone it tilted towards the driver.

Dashboard Mount for a Toyota Tacoma - Note 10 Plus Sized (With Case) -Standard Mount sits above the dash allowing All Infotainment controls to be accessed. -Lowered Mount is Lowered but will Block Air vent and Stereo buttons a little bit, but to me...

... on its side as the layer lines help add to the carbon fiber look. There are 2 models, 'Tacoma Tray Charger Carbon' is what is pictured that I printed for my truck before having the idea for 'Tacoma Tray Charger TRD' where I added a TRD logo to it.

It sit in the little square cup holder in the middle and will allow you to place your S21 or smaller phone next to the shifter to have a convenient storage position for your phone. I printed it upside down using supports since it resulted in the...