tamiya bruiser shocks 3d models

Rear bumper for Bruiser. ...I did smooth with acetone vapor bath and painted.

rims for tamiya bruiser , for 1.9 tires . ... 2 type of offset

2.2 Wheel rims for the Tamiya Bruiser and HG P407 , these are 20mm narrower that stock , 10mm off each face , there are two types , front and rear , the fronts have built in 6mm spacers to correct the track of the stock vehicle , if you don't want...

also suits hg p401 bruiser clone chassis includes optional spare tyre hanger which suits upto 110mm tyre

created from a sketch, it is in the right dimentions but the details are done from pictures.

This is a part of RC Car HG P407\Tamiya Bruiser. ...Front bumper holder.

Wood effect sides for the load area of a Tamiya Bruiser or HG P407

This is a part of RC Car HG P407\Tamiya Bruiser. ...Front bumper holder.

Replacement front body mount for Tamiya Bruiser and P407 clones. I used a spare screw I had laying around to mount it to the bracket. You'll need to hold the printed part with pliers to thread the screw into it. I recommend printing with PETG...

They should also fit on the genuine Tamiya Bruiser. I also added a wheel spacer. It can be scaled in the Z-direction to any thickness. -Break off the support plate under the roll bar after printing. -Break off the support rings around the wheel...

An adapter that bolts to an original Tamiya Bruiser or 1981 Hilux axle to convert it to a TLT hub allowing you to have a 12mm hex. Design inspired from the 'rummy mod' back in the day. To put this on an axle you will need to cut the ends off...

this is a 1.9" wheel i designed for the bruiser / hg p407. it is a little wider than standard wheels to allow you to fit wheel weights into the centre of the rim. I got the wheel weights from Ebay and are actually for full sized car wheels and are...

Simple shock towers to run 70mm long shocks on a Tamiya TT-02. These were designed to be used in conjunction with my Tamiya TT-02 Capra Body modification but can be used with a normal TT-02 as well. These just bolt into the existing shock mount...

3 diferent sizes preload spacers for original tamiya cva black shocks -4mm -3mm -2mm

I designed these to improve the stability in cornering and prevent tire rub. ...They are a direct fit for the stock wheels.

Works good, remove hub slide on redid it so it goes all the way down to axial just like stock. ...added another one to try...

... bed. ... Put in the way that appears in the image to use fewer supports, does not need rafts ES: Based on the cover of the Tamiya Bruiser, it fits the WPL c24 case Put in the form that appears in the image to use less supports, it does not need rafts

Hi, just lower wishbones for bigger shocks. You need the long for the back and the short in the front. You will gain some ridehight, but I hoped it will run smoother. ... Have fun!

HG P407 Tamiya Bruiser Clone Servo Mount Halterung, Savöx Servo. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...

HG P407 Tamiya Bruiser Clone Front Bumper. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von schmelz.bar empfehlen....

HG P407 Tamiya Bruiser Clone Servo Mount Halterung, Savöx Servo. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament...

HG P407 Tamiya Bruiser Clone Front Bumper. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses Filament von...

HG P407 Tamiya Bruiser Clone with RC4WD Chevy Blazer Body + ESS-One Mount. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses...

HG P407 Tamiya Bruiser Clone with RC4WD Chevy Blazer Body + ESS-One Mount. Durch meine nun mehrjährige Erfahrung im 3D Druckbereich und etlichen versuchen mit verschiedenen Materialien von unterschiedlichen Herstellern, kann ich definitiv dieses...

It's intended to allow the use of 1.9 tires without increasing Bruiser's track width by converting the hubs to hex 12mm. This rim design has been inspired by Bonkett's model also available on Thingiverse, but I wanted something that looks more...

Used these Shock towers to fit 90mm shocks to a Tamiya TL-01 chassis. Together with a reduction gearbox (I will upload this later) you can fit bigger wheels to get some kind of TL-01 crawler. There are also mounting points for Carson...

Used these Shock towers to fit 90mm shocks to a Tamiya TL-01 chassis. Together with a reduction gearbox (I will upload this later) you can fit bigger wheels to get some kind of TL-01 crawler. There are also mounting points for Carson...

This is a remix of Bisbiglio74 1.9" rims for a slightly more refined cosmetic look and has two files , one is normal thickness and the other is for the front only and incorporates a 6mm spacer to widen the front track to match the rear .

Shock Absorber

A multipurpose shocks