tcl tv stand legs 3d models

Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately) Category: Replacement Parts

Fold-able legs/stand for TCL TV so that you can fold them in and hang the TV on a wall (I have a wall mount I will share seperately)

this is a shorter and simpler version of the 3DbyJB TCL ROKU tv leg. this will fit 40in and 43in TCL Roku tvs. ...

Designed this for my TCL TV with a 10mm thick border. ONE LAYER contains bridging. ... .2mm

These are just a couple of tv legs I designed and printed for my roommates tcl smart tv.

tv legs for fujicom tv. simple design... ...painted it black with gold dots.

A simple design I've made in order to convert some old shelves in to a TV stand. The shelves are incredibly strong under compression, more than capable of holding my own weight when I tested it so they can easily hold this 50" TV and a few games...

legs for my fujicom 51 inch tv. ... in the future i will refine the model with smoothing and black paint, will update...

TCL 55C715 only with wall mount

TV LEGS FOR NEC 42" PLATINUM MONITOR

This spacer is meant to raise your TV off of the stand. In my case I use the TV's for side PC monitors and wanted to raise them to be level with my actual gaming monitor in the center of the two. By default, these are .625" high, but you can...

I designed this to hold my sound bar. ...If you look closely at the top of the tv, it has a slight forward slope. ...That and the curved back, required some accurate measurements and a few iterations.

My sons TCL 43" Roku Tvs base legs were to short to fit his Xbox One and cable box under it so I designed 70mm tall ones and printed them on my Ender 3 Pro. ... These fit perfectly using the existing screws.

Simple holder for remote control of my TCL TV. You can use 2 screws to fix it to the wall. Works fine. ... Enjoy ;)

TV support used to raise the TV in order to place the soundbar below and not interfere with communication with the remote control.3D printing support is difficult to remove. ...Minimum filling of 25% recommended

The TV legs that go on the bottom a Kogan TV and will take 3/16 inch (4mm) metal thread screws to attach to tv base.

Do the legs on your Samsung Smart TV not quite let you place your DVD Player, Gaming Console, Sound System, or other electronics directly underneath? Do you think a simple piece of plastic shouldn't cost $10+? Look no further! Designed for a 32"...

Made these for the series 5 50S535-CA because the legs were too wide. I've included the part files as well, print with at least 70% infill, don't need support but up to you. Please not you must print both copies, the left side has a slightly...

This mount allows you to set a TCL 43" 4K TV on its back for the purpose of using it as a digital gaming table to display maps. The height matches the bottom section of the TV so you only need two prints to hold the top corners for the TV to lay...

... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.

... accept them (filesize), but you get the idea. ...It sits on top of a TCL TV perfectly. It's a 12mmx12mmx12mm rectangular holder and you can screw your wyze cam pan v3 to it. Super simple stuff, no bridges or supports. ...Print it however you want.

This is a replacement battery cover for a TCL Roku TV remote. There are several versions of Roku TV remote, so this may not fit yours. The STEP file was included in case you'd like to adjust it to fit yours. The Airtag cover is still not perfect....

A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.

A simple remote holder for TCL brand Roku smart TVs. ...Mounts with either two screws or adhesive similar to a command strip.

Based on https://www.thingiverse.com/thing:4253124, however upon testing, these feet did not fit or work with my TCL 55S425, so I designed and printed some from scratch. Then I added a sound bar and made the extenders to allow for the remote to...

For pallet wall mount for tv

This is a replacement battery cover for a Roku remote for TCL TVs. I made this because I hate searching for the remote, and I didn't want to buy a new one that does allow tracking. As a side benefit, the extra length makes it easier to grip the...

... recommend using a plastic of high strength with a high infill percentage. The idea of this was still designed with some sort of support underneath (like a shelf), but with proper layering and infill these could support the TV on their own. ...

Requires two additional screws to mount the soundbar onto the part (in addition to the two screws to mount the whole thing to the TV). I initially designed it to where a part of the print fit into the back of the soundbar and no screws were needed,...

Since I have a TCL Roku 4K tv, I have to use IR when it comes to controlling the volume on the TV. The Apple TV has to be visible, so I decided to take an Apple TV mount, and put brackets on it to fit the TV. It worked quite well. The reason the...