the nexus mounts 3d models
2826043 3d models found related to the nexus mounts.myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2013 version of the Nexus if you have a 2012 version check out this Mount I made for the 2012 version
myminifactory
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 version
thingiverse
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2013 version of the Nexus if you have a 2012 version check out this Mount I made for the 2012 versionhttp://www.thingiverse.com/thing:591287 Also...
thingiverse
it mounts into the not used antenna hole in the flysky/iris transmitter this man only works with the 2012 version of the Nexus if you have a 2013 version check out this Mount I made for the 2013 versionhttp://www.thingiverse.com/thing:591294 Also...
3docean
Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi Format) - *.mb (Maya 8.5) - *.lwo (Lightwave 6) - *.c4d (Cinema 4D 11) renders Are made in 3ds Max 2008 using...
thingiverse
This is a holder for the Nexus GPS mount. It clamps to car mirror mounts with 16mm ball joints. ...Fits M4 cylinder head screws and nuts, so clamping force can be adjusted.
cgtrader
Itâs created accurately, in real units of measurement, qualitatively and maximally close to the original.Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx (Multi Format) - *.obj (Multi Format) - *.3ds (Multi Format)...
thingiverse
NEXUS 7 (2013) Stand You can be used in the state in which you installed the "VERUS" case. ... http://blog.grooboo.net/cryde/
thingiverse
This is a holder will allow your Phantom Vision clamp to hold your Nexus 7 Tablet. ...This was designed with the 2nd gen version of the tablet. I used the default settings for printing. Instructions I used the default settings on my Replicator 2.
thingiverse
One is for the four symmetrical mounting holes, the other one is for the centered mounting hole. There are two stl files. One is to fit a bare 5X, the other one is to fit a 5X with a thin case. ...Remixed from:http://www.thingiverse.com/thing:1792532...
thingiverse
Phone case with The Zeitgeist Movement logo on it :)
thingiverse
Here are a couple STLs for The Great Discus FPV frame The ugly mount should be able to mount onto 15mm standoffs as long as they are around 4mm or slightly less. Here is a link to the ones I use. https://s.click.aliexpress.com/e/_DFpuoxt The other...
thingiverse
Could be used on the night stand.
thingiverse
neXus Camera mount. ...Developed for the TinysLEDs' neXus quad frame. Mounts on 30mm standoffs. Holds FPV micro camera. Print 1 for each side. [Updated] Files are now oriented as they should be printed. ... [TinysLEDs](http://www.tinysleds.com)
thingiverse
This is a snug fitting tripod mount for the LG Nexus 4, it uses an M6 Nut at its base Instructions Autodesk Inventor
thingiverse
(An M6 Screw will be needed.) The mounting hole is offset higher than the Nexus Player's center of gravity, to avoid the mount rotating 360 degrees and to keep the device from falling out. ... (Yes the word "mount" is in this summery quite a bit, I...
thingiverse
... a reference model of the Nexus Player. The monitor mount pictured beside it is @puttelino's VESA 100 monitor mount, http://www.thingiverse.com/thing:213186. ... It might be possible to remix these two and have a monitor and nexus player wall mount.
thingiverse
I used the excellent 3D model from here:http://grabcad.com/library/samsung-galaxy-nexus to generate a "mold" that I worked from. Note that as uploaded the volume buttons and headphone jack are not accesible. Instructions Consider Mounting. If you...
thingiverse
Simple Nexus 5 mount that fits 35mm tube. The phone start button is easily reached from the handlebar making it easy to toggle the screen on and off while using GPS. ... Requires 4x M3x20mm + nut's.
thingiverse
This is a remix of the well done Nexus 10 Wall Mount by dfoles. ...I wanted to hide the screw holes and make it slide in and out from the top.
prusaprinters
'Naked' mount without holes. Fits Nexus 5 perfectly, on the bottom a gap has been left out so the usb cable can fit and microphone and speaker still work. Category: Mobile Phone
thingiverse
'Naked' mount without holes. ...Fits Nexus 5 perfectly, on the bottom a gap has been left out so the usb cable can fit and microphone and speaker still work.
thingiverse
This is a wall mount frame for the first Nexus 7 tablet, ideal to use an old tablet as a kiosk for home automation. ... No specific printing settings is needed Just use 3 nails to hang on the wall.
thingiverse
Mount your old Nexus 4 to a vertical surface. Possibly as a controller for home automation. ...Post-Printing
thingiverse
This is a tripod mount I made for the Nexus 5. I would recommend printing with supports and any of your usual other print settings. ...The mount is for use with a Quick Release as you can see by the image.