tilton brakes 3d models
12386 3d models found related to tilton brakes.
thingiverse
Customized version of https://www.thingiverse.com/thing:52734 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=52734
grabcad
Tilton racing pedal assembly brake & clutch with separate master cylinder reservoirs
pinshape
A simple 15mm spacer for you pedals You can adjust the height of the spacer simply by scaling the z axis These are the pedals I am using https://pinshape.com/items/57737-3d-printed-logitech-tilton-style-pedal-faces
grabcad
Weighing only 4.5 lbs., this flywheel is made by Tilton only for Porsche Motorsports. Uses a 5" dia. clutch pack. ...(and was also made by me because $2500 is a little pricey from Porsche)
pinshape
Tilton style pedal face for Logitech G25,G27,G29,920 This pedal face is more comfortable than the stock plus you can adjust the height using this spacer that I highly recomend https://pinshape.com/items/57738-3d-printed-logitech-tilton-pedals-spacer
thingiverse
Tilton style pedal face for Logitech G25,G27,G29,920 This pedal face is more comfortable than the stock plus you can adjust the height using this spacer that I highly recomend https://www.thingiverse.com/thing:3752551
thingiverse
These are tilton style pedals to fit logitech pedals.Based on the DSD pedal pads:http://www.derekspearedesigns.com/tilton-style-pedal-pads.html They have an option to add your initials or amend hole spacing for different pedals (fanatech etc) by...
thingiverse
Tilton pedal with holes 22mm apart. It will fit the T300RS (2 pedal) for sure, as I have this one myself. If any adaption is needed for T3PA, LCM, ... ...Let me know the spacing required or send me a pedalset ;) use bit longer M3 bolts, since...
thingiverse
This is a replacement lid for a Tilton master cylinder triple reservoir . Don't use support or it will clog the threads. Print with top up, as the buttress thread will string if printed upside down . 2 versions available, with or without some...
grabcad
Based on the Tilton 3D Model from their site, visual detail added. Note, this model is my interpretation of the unit and is not intended as an authentic copy of the original. ...That said it is fine for accurate installation positioning and is...
prusaprinters
Tilton pedal with holes 22mm apart. It will fit the T300RS (2 pedal) for sure, as I have this one myself. If any adaption is needed for T3PA, LCM, ... ...Let me know the spacing required or send me a pedalset ;)</p> <p>use bit longer M3 bolts, since...
grabcad
Parts downloaded from Tilton and modified to allow for complete range of motion, including brake bias bar:Tilton Pedal Assembly 72-603Tilton 76 Series Master CylindersTilton Brake Bias BarTilton Throttle Cable Mount 72-791Part modelled by myself...
grabcad
Master cylinder to be used in braking systems, brake pedals or hydraulic handbrake assemblies. 1.1" of travel. The mates in the assembly are set in a way that you can move the shaft throughout its 1.1 inch of travel. ...
thingiverse
Update (Dec 19, 2020): Mixed a 2 cm wider brake pedal to make heel and toe easier; the new stl is "Tilton_11.4cm_7.4cm_brake_wide.stl". I started with a Dynamic Profile for PLA in CURA and tweaked it for 150% extrusion for strength; this profile is...