tk1 jetson 3d models
460 3d models found related to tk1 jetson.
grabcad
Updated STLs for the Nvidai Jetson TK1 Case I designed. Includes ports for the SD Card, JTAG, SATA Power, and all outfacing connections. ...Print at 1.01 scale.
thingiverse
A cover for the new Nvidia Tegra K1 powered Jetson TK1. ...This is a remix of https://www.thingiverse.com/thing:348473
thingiverse
A simple enclosure for NVIDIA Jetson TK1 dev kit. ... You need only 4 hexagonal spacer sleeves, 4 screws and 4 bolts.
thingiverse
This is a simple plexiglass case for Nvidia Jetson TK1. To be produced with a laser cutter. ... Materials Needed Requirements Plexiglass 4 x screw M3 (length depend on plexiglass tickness) 4 x nut M3 A...
youmagine
It is only 5 ½â square, however, so unlike my P2C2 case, it can be printed on most 3D printers made today.The case holds not only the Jetson-TK1 board, but a 2 ½â SATA drive too. It is also possible to install a circuit board of your own design...
thingiverse
Two piece case for the Jetson TK1 development board. Instructions The board fits well when printing ABS at 101% scale. Tap holes in top for M3 or similar screws to hold everything together. ...Slots...
thingiverse
These are the right sized spacers for this jetson tk1 case: https://www.thingiverse.com/thing:348473 I used 4x 1.5" 4-40 screws
thingiverse
I decided to share the clips I designed for mounting the TK1 onto an F450 quadcopter frame. ...Hope this helps somebody.
thingiverse
A cover for the NVIDIA Tegra K1 powered Jetson TK1 (NVIDIA logo). ...This is a remix of https://www.thingiverse.com/thing:348473
thingiverse
Minimal case for the NVIDIA Jetson TK1 development board. Very basic...a top and bottom piece supported by standoffs & hardware...it keeps fingers and dropped tools off the board on one's desk, doesn't accommodate drives or add-ons. Yeah, this would...
youmagine
I added 'quilting' to the large flat top and bottom parts of the tonyvr's ketson tk1 case http://www.youmagine.com/designs/7819 to reduce warping.
grabcad
Just a rough design, as i was in need of it urgently. Sharing, so that others could have some help. ...Mistakes are excused :D
thingiverse
Derivative of Sneeze Guard case, without the cutouts in the top plate. Standoffs required are 1 inch. ... Non printed parts in attached PDF BOM (for Australian electronics store, Jaycar) Assembly instruction in attached illustration.
thingiverse
Converted and split into multiple files to fit on a 220mm print bed
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options:...
thingiverse
Customized version of https://www.thingiverse.com/thing:1516585 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1516585
sketchfab
TK1-SP Weed killer Kit with UP2/E pump and 107 l tank Tank kit for fresh or salt water, complete with pressure pump. ...Suitable for shower systems, sinks and toilets.
sketchfab
TK1-SP3 Weed killer Kit with UP3/E pump and 107 l tank Tank kit for fresh or salt water, complete with pressure pump. ...Suitable for shower systems, sinks and toilets.
3docean
TK1-009 Travel Run Animation Data For very small characters with very short arms-legs, and four fingers on hands. ... · Frame Rates : 24 fps // 30 fps · # frames : 239 // 307 · Formats : .bvh .bip · Version (Review) : 3.51a ( 2015/11/02 )
3docean
TK1-008 Fast Run Animation Data For very small characters with very short arms-legs, and four fingers on hands. ... · Frame Rates : 24 fps // 30 fps · # frames : 241 // 301 · Formats : .bvh .bip · Version (Review) : 3.51a ( 2015/11/02 )
3docean
TK1-007 Chase Run Animation Data For very small characters with very short arms-legs, and four fingers on hands. ... · Frame Rates : 24 fps // 30 fps · # frames : 239 // 297 · Formats : .bvh .bip · Version (Review) : 3.51a ( 2015/10/31 )
3docean
TK1-006 Huffy Walk Animation Data For very small characters with very short arms-legs, and four fingers on hands. ... · Frame Rates : 24 fps // 30 fps · # frames : 241 // 301 · Formats : .bvh .bip · Version (Review) : 3.51a ( 2015/10/30 )
3docean
Toon Kid 1 – Stroll Walk TK1-004 Animation Data For very small characters with very short arms-legs, and four fingers on hands. ... · Frame Rates : 24 fps // 30 fps · # frames : 241 // 302 · Formats : .bvh .bip · Version (Review) : 3.51a (...
thingiverse
This is a simple base for a [TK1 Soviet telegraph key](https://www.radiomuseum.org/r/military_telegraph_key_tk1.html). Although it doesn't really provide enough weight for efficient use of the key, it is compact and portable. The base is attached...