traxxas slash skis 3d models

this is only one side of the ski but mirror the ski and you will get the other side

These can replace your regular tires for use on packed snow

skis for 1/10 traxxas cars

Works for Traxxas 2wd Stampede and 2wd Slash. ...Print the axles solid.Uses m3 nuts and 25mm m3 bolts.

Traxxas TRX4M Trailer Skis! ...

twin tip skis for traxxas slash. you will need to download the upright of your choosing from the original thing. I recommend riveting a piece of plastic to the front of the ski for better performance in deep snow. ... This is a remix of...

hey, made some skis for my slash 2wd. ...skis are printed with pla and linkages with flexible filament https://youtu.be/sRequv5ERdY

traxxas slash accessory

Battery cover for traxxas slash. ...

a-arm for a traxxas slash

Dual 7 cell baterry adapter for traxxas slash

SummaryEDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash

this is the traxxas slash 1/10 scale battery adapter post. ...fits fine in the chassis.

EDIT: updated with newer design rear carrier for the 1/10 scale 4x4 traxxas slash

86 tooth pinion gear for Traxxas Slash 2wd and 4wd models.

this is the traxxas slash 1/10 scale battery adapter post. ...fits fine in the chassis.

the lower shock spring support for the suspension on the 1/10 scale traxxas slash.version of this with an integrated guard platehttps://www.youmagine.com/designs/traxxas-slash-shock-guard-81b09451-49bd-4154-8d65-b13669b0461c

EDIT: model has been updated with tighter dimensionsrear carrier for the 1/10 scale 4x4 traxxas slash

the 2 holes in the middle of the part are for attaching an additional center brace for extra support.brace for mounting between the bumper armshttps://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracerear bumper...

EDIT: part has been updated with tighter dimensionsa rear bumper for the 1/10 scale traxxas slashbumper arms can be found here https://www.youmagine.com/designs/traxxas-slash-bumper-arm-bracesupport brace for the rear bumper...

a front bumper for the traxxas slash 1/10 scale 4x4 RC car uses the mount from the RPM aftermarket front bumper. ...has holes for 10 LEDs

Traxxas Slash Truck pulling Hitch. ...Recommend 100% triangular infill PLA Plus, Pro , Tough You will need to drill the drive side holes all the way through.

the front to the traxxas slash 2wd model. ...i haven't printed it yet so please tell me if it works Instructions print with 100% infill

These are extended body posts for the traxxas slash or other vehicles that use posts that have a screw hole on the bottom of the post

the lower shock spring support for the suspension on the 1/10 scale traxxas slash. ...version with shieldhttp://www.thingiverse.com/thing:1175692

EDIT: model has been updated with tighter dimensionsfront steering block for the traxxas slash 1/10 scale 4x4 RC car. ...bearings fit perfectly

This is a GoPro mount I modeled for the Traxxas Slash. ...It has a support piece that helps keep the GoPro from rolling forward and back.

this is a lower spring support for the suspension with a shock guard added to it, it fits the stock springs, not sure about big bores.version with a shorter shieldhttps://www.youmagine.com/designs/traxxas-slash-shock-support-and-guard-shortversion...

This is just a fun decorative addition to my Traxxas Slash. Instructions Print both pieces with 100% infill with no rafts or supports. ...Place pieces on the front bumper and hot glue together.

Traxxas SLASH RC truck roll bars. These are cosmetic and really improves the look of the truck. ...I fastened them to the body by drilling holes and using little screws.