traxxas spur gear 3d models
82585 3d models found related to traxxas spur gear.thingiverse
Anyways I had to get a new pinion, but there aren't any 48p 5mm bore pinions, which meant I had to buy a different pitch pinion, which also means I had to buy a new spur gear to match, but there also isn't any traxxas spur gears for my car with...
thingiverse
This is a 32 pitch 56 tooth spur gear I designed for my Traxxas Slash. It is designed to require no supports, I used a 15 tooth pinion with it. It uses three 6mm m3 screws. It looks a lot different from the stock gear, but it is so that it will...
thingiverse
I designed this traxxas spur for my stampede 2wd. You might need to warm up the piece to fit the bearing in. Make sure to spray your build plate with adhesive to prevent it from warping. It is best used for a temporary fix waiting for the part to...
sketchfab
Just a quick Herringbone gear to be used for a Traxxas rustler/bandit/slash.
thingiverse
This is a splined replacement for the trx4 45 tooth spur gear. it does not use the friction material from the slipper clutch but does use the plates to help with centering. i would reccomend cranking the mounting nut howver just to help prevent...
thingiverse
good upgrade for a absima to a more common type of spur gear
thingiverse
A 3D printable 90 tooth spur gear for 2 wheel drive Traxxas models. ... https://www.youtube.com/watch?v=LV5MNS3CUnk
thingiverse
I printed this out of PETG and have briefly tested on concrete at full throttle starts on a 3s battery so far it's holding up.
thingiverse
Spur gear, 38-tooth (1.0 metric pitch) for Traxxas Revo 3.3. Part number 3954 Don't bother printing this in PLA, ABS or PETG... ...needs to be something with a carbon compound in it because this gear has a lot of torque applied to it.
myminifactory
UPDATE: Uploaded the wrong file by mistake so please dowmload the gear-Bv2 . Sorry for the mistake Broke the plastic spur gears on mt traxxas 2075 servo so designed mt own , you might have to file the centre holes a tad bit to fit but working...
thingiverse
Replacement spur gear for Traxxas RC cars such as the Traxxas Rustler 4x4 VXL (for which I designed this spur gear). I have gone through a few designs and this one seems to do the job the best. Should work fine with other Traxxas models, as long as...
thingiverse
This contains a Traxxas 46p 76-tooth spur gear (among others and pinions) which I use for my Slash 2WD RC car. It is a high quality and accurately measured 20th generation design which I am currently racing with, and it prints well even on my...
thingiverse
Also see the Traxxas 4676 spur gear. V6 is a redesigned spur with a smaller diameter, therefore more accurate teeth spacing and less stripping. ... It also has my signature three decorative holes for making it lightweight and saving some PLA (but it...
thingiverse
Traxxas 3953 Revo 3.3 Spur gear 36t mod 1 Mod: 1 Tooth : 36T Center Hole Diamter: 10.8mm Gear Thickness: 6.5mm Tooth Pressure Angle: 14.5 https://www.youtube.com/watch?v=I9aLtHVO5V4 Video : This is Revo 3.3 converted to brushless
thingiverse
Just a simple 50 Tooth Spur gear. Maybe needs a bit of modification, depending on your Printer, Material and Settings. Print with very low outer Wall speed to get clean tooth. If your printing with nylon, be sure to use some kind of Bed adhesion...
thingiverse
This is a Traxxas Slash 2WD 1/10 model 64t (64 teeth) spur gear. I plan to use it with the 28 tooth pinion gear I just posted. It will not work with the 23 tooth pinion or lesser toothed pinion gears because it is smaller. This is not based on any...
thingiverse
This is a 73t 46p spur gear for Traxxas Slash 2WD. It should work with a 23 tooth pinion or larger. I never used it yet so please leave me a comment or like if this works. ...Thanks!
thingiverse
This is a 46p 67t (67 teeth) spur gear I made for my Traxxas Slash 2WD 1/10. It's probably the fewest teeth on a spur gear that will work in combination with a 23 pinion gear. This baby zooms on my RC, but you really need to ease into the throttle...
cults3d
Print with 100% infill at the lowest layer hight your patience can bear. ...Will not be as tough as the molded plastic one, but you can aways print another!
thingiverse
Print with 100% infill at the lowest layer hight your patience can bear. ...Will not be as tough as the molded plastic one, but you can aways print another!
thingiverse
Fits my car nicely (as shown on the photo). Print the STL upside down in PLA or nylon, no supports required. ...Extra perimeters are advised.
thingiverse
A spur gear for a traxxas rc car with 50 teeth. Read instructions ! Instructions V1.1 did not publish. UPDATE v1.2 model has a solid side added for better printing. UPDATE V1.3 tuned holes for...