traxxas trx 3d models

Protection TRAXXAS TRX-4. ...Scale 1/10.

Bumper, and window rock guards for the Traxxas Trx-4

This is a very close 3D replica of the Traxxas TRX-1 chassis. This would be a little difficult to print but I guess it could be attempted with a carbon fiber filament. The main issue would be the strength of the front chassis kick-up. A better...

A Pair of stands to support the Traxxas TRX-4 Series chassis, taking the weight off the tires. ... The front steering hubs sit in the front stand saddle whilst the rear stand tucks up and supports the bottom of the portal hub

Borrowed our Traxxas TRX-4 show truck from work, and wanted to make a towhook/mount for it. Have not printed it yet (the printer is working at the moment), but I think it will fit good, and made a 3mm hole so you can make and mount your own kind of...

This is a stand that i designed for any Traxxas TRX-4 using the stock 95mm shocks (or shorter). This stand allows you to lift the vehicle off the wheels for storage. By lifting the vehicle off the wheels it helps prevent flat spots of the tires and...

A Stand for the Traxxas TRX-4. It isd designed to hold the Car up in the Air so the Suspension gets relaxed. You can put this Stand in booth Drive Directions under the Car. It doesn't matter. To screw it together use M3x16 or M3x12 with a Washer....

Ständer für einen Traxxas TRX Defender 1:16

This component is for a Traxxas TRX-4 it is in mm.

This bumper is for the Traxxas trx 4 defender This is using another bumper: https://www.thingiverse.com/thing:2724390

This is my Traxxas TRX-4 1cm Lift Kit to make the trx-4 fit 2.2 tires Parts you will need need for mounting: 4 M3x18mm screws

Wheel up for Traxxas TRX-4 Support - YES Infil - 100 Material - PLA ABS You will need a bolt and nut M3

Just a simple remix of the stand sized for a Traxxas TRX-4. Print 2 of each as they are orientated in the STL. Used 8mm x 3mm thick rare earth magets. ... Holes may not be perfect as the print I used for this print a hair on the small side.

Wall mount for the Traxxas TRX-4 and other similar RC trucks/cars It hooks around the rear axle of the vehicle and screws to the wall with two #10 wood screws (canada, not sure if there is a metric equivalent - 0.193"/4.9mm diameter thread). You...

A TRX-4 stand to lift the tires off the shelf to keep them from getting a flat spot.

Wanted a bumper for my TRX-4 with a Axial Cherokee body on it that would fit in tight to the rear of the vehicle and not hang down very low. I used a bumper mount with very little drop and as far out on the frame as I could get. Added a spare tire...

Jeep hardbody mounting to Traxxas TRX 4 with magnets

Door hinges for Traxxas TRX-4 Land Rover Defender body. ... Edit: Added all body hinges.

This a end that goes on the Traxxas Trx 4 to make it have a more scale look.

Snorkel grill for Traxxas TRX-4 Land Rover Defender body. There are four types. ...Choose which one you want.

Snorkel grill for Traxxas TRX-4 Land Rover Defender body. There are four types. ...Choose which one you want.

Simple battery hold down for large battery (in my case 3-cell Lipo 155x42x44 mm) in Traxxas TRX-4.

Ersatzteil für die sehr instabile Achsaufnahme vom Traxxas TRX Nitro Sport .15. ...Beim Drucken muss ein wenig experimentiert werden, die Maße stimmen allerdings alle!

Can for Traxxas TRX-4 Land Rover Defender body. Three types: Same as original (double), with a hole. Same as original, without a hole. ...Not double.

 Can for Traxxas TRX-4 Land Rover Defender body. Three types: 1. Same as original (double), with hole. 2. Same as original, without hole. 3. ...Not double.

Door handles for Traxxas TRX-4 Land Rover Defender body. Holes are for 2 mm screws. Back plate is scalable in z axe to have optimal thickness. ... Edit: added holes handle 2 and 3

Front shock tower for the Traxxas TRX-1 (4708 / 4718). This is modeled very closely after the original design. ... NOTE: I have not yet overlaid this on the original tower, but I believe it to be very close.

TRX-4 front body mount post to relocate battery over axles. ...Two versions available standard and individual posts to allow 41mm of battery width. Body hole spacing is for stock Traxxas TRX-4 bodies. ... 4/17/19 - v2 lowest setting useable

Universal ESC adapter for Traxxas TRX-4 I made this to adapt a Surpass Hobby 60A ESC, without having to glue the ESC to the TRX-4. Enjoy and click the heart if you like it. ... Comment if you want an adapter for other R/C.

Front shock tower for the Traxxas TRX-3 and TCP buggies (2626). These files can be used to create your own shock tower. ...There are also great options available from vintage reproduction suppliers (ex.: Factory Works) for reasonable price if you do...