trx4 link riser 3d models
112718 3d models found related to trx4 link riser.
thingiverse
This is a link riser for the upper links of an axial capra rc car. It raises the rear upper links 10mm while maintaining the correct distance from the chassis. I print with supports, 4 perimeters. Use the stock link screws to attach the riser to...
thingiverse
Link riser for rear axle of the Traxxas TRX-4. Multiple Heights in different files. ...Print on flat side and no support needed.
thingiverse
Simple link riser for the Element Enduro. I made this to prevent binding between the upper and lower link when using the Rock Pirates Interceptor chassis and artful dodgers skid. I'm using as single sheer, but you can easily print 2 and use spacers...
thingiverse
A simple piece that slots into the stock axle truss, uses stock upper link mout and upper link mount screws for attachement. recommend to Print at 0.1 layer heights and 4 walls / 8 top bottoms, for better strength and detail. the holes on top...
thingiverse
It is finally here, minor tweaks may come, but this is it finaly a 4 link centre skid for the trx4. this will convert your trx4 into 4 link suspention. You will need my servo over axle, and 1 set of rear links upper and lower. this can also be used...
thingiverse
AR44 Link Riser in 3 different versions. Straight, forward facing, and rear facing to suit different link lengths and clearance for some setups. PETG has held up so far, but recommend nylon if available for best results. Very high to 100% infill...
prusaprinters
This is a link riser for the rear upper links of an axial capra RC car.I found that the print orientation has a huge effect on the part's strength.PLA or PETG at 100% infill works well.
thingiverse
Axial Wraith 2.2 use the AR60 axles and could not find a link riser for the rear upper link mount that could be 3d printed. These both utilize the servo mounting position on the factory upper axle truss. The standard version uses the same link...
myminifactory
Adjustable rear link riser for the SCX24. The goal is add anti-squat to the suspension. There are two options. One is the same width as the stock mount and the other is 6.5mm wider (3.25mm per side) to improve sidehill performance. ... Clean out the...
thingiverse
... down w tree support, but standing on its end may be stronger. I have had no durability issues but i do not treat my crawlers like bashers. 35% infill you will need two 3x20mm screws to go through the links stock screws will mount the riser to axel
thingiverse
rises the rear upper links, this lets your rear suspension have more articulation with aftermarket or double barrel shocks while also preventing the links from hitting each other when using high clearance links. ...this part may cause the upper links to...
thingiverse
Français Support de Bavette arrière pour " TRX4 " Anglais Rear Bib Support for "TRX4"
thingiverse
These are spacers to go under your stock TRX4 Sliders. they are designed to be a snug fit to limit any additional movement. These Spacers raise the slider 13mm to make them nearly flush to the bottom of the chassis. you will need longer bolts 20-22mm...
thingiverse
Rear battery tray installs using zip ties 25mm links work great with angled ends to replace those crappy upper links that come with the kit. The body mount puts the posts in standard TRX location (relative to axle). You'll need the TRX4 bit with...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=58355 Instructions Using the following options: Font = write/Letters.dxf Riser_Angle = 0 build_plate_manual_y = 100 build_plate_manual_x = 100 build_plate_selector = 2 Riser_Length = 3.25...