trx4 shock mounts 3d models

This is a rear TRX4 shock mount with a lot more mounting options. I also wanted to make a mount with a lower profile to fit with a pickup bed that I have designed and uploaded also to here. ... Printing: Solid needs supports

I wanted to see what would happen with some longer shocks and relocated top mount points. The end result was an extra 3cm of full flex travel over stock. This is with 90mm front shocks and 100mm rear. I am using the RC4WD King shocks with the faux...

... ~$8.00 USD to an online service for the parts to be cut from 6061 aluminum. Note that I'm using 120mm shocks and "1/10 RC Aluminum Front/Rear Shock Tower Hoops Bracket Mount for TRX-4". ... The longer shocks are not required, though the hoops are.

4 screws to fit/remove, 3 to the portal and one to the shock, i used the screws that were already fitted no need for any additional length, the cap heads need to sit within the plastic of the mount i had to carefully run a 4.5mm drill in just to...

Shock support for Traxxas trx4

This is a replacement shock tower for the shortened front suspension of a TRX4

TRX4 custom Shock absorbers holder

A shock holder for filling stock trx4 or trx6 shocks, springs must be removed and the top shock collars must be installed. The holes are 13mm. Print in default orientation, supports for the holes optional. ...This is my first design in a new cad program...

There are 2 different mounts. ... V3 shocks a bit tighter for the plastick shock caps V2 alloy shock caps

New Diff shock mounts for the Ursa Bear. ...Turned around so the shocks can be removed with out having to remove the hubs/wheels.

Top and bottom mounts to mount a shock absorber to a box trailer or camper trailer, I designed and made these mounts to fit my camper trailer. Note the shocks should mount as close to vertical as possible, no more than a 30 deg lean. The flatter they...

I designed these shock mounts for a TRX4M Bronco. ...You can choose different angles to soften the shock and add more flex. *Edit: I added a V2 for the front shock mounts. ...They clear the Bronco body brace a bit better and have more mounting holes.

Retraced the Mesh of the original design to get a full CAD model. ... Need to work now on trackbar/panhardbar connection to the front left shock mount..

Works great with my high clearance IFS mod since that changes the lower mounting point, you can use longer or shorter shocks and place them where they will work best. Interchangeable front or rear, doesn't change the body mount post position. Just...

To accommodate their mounting I've created a modified front and rear shock mount each with their own Tarmo logo on them. I've also included each version without the logo as well. Dependent on orientation the rear mount logo may need to be supported,...

Mini-t spring cups for TRX4 shock absorbers

fast to print and fast to mount, shocks for bison vkar and helion rc car. ... -print and mount whit any 3mm screw -infill 15% or higher -Layer height 0.15

Front and rear low clearance bumper mounts, rear high body mount and low profile dropped rock sliders. Bumper mounts set for Axial JCR Concepts bumpers. The TRX4 Sport kit is awesome but the stock body lacks appeal and is quite heavy at 275gr (465gr...

If you broke panhard mounting on left shock tower on your TRX 4 NOW you can print Left and Right NEW Shock Tower w/panhard mounting V 1.8 finally

My chassis had cracks in all four shock mounting areas, so I created this part to reduce the stress to each point by spreading the load. It also places the shocks more upright and makes adjustments to threaded shocks much easier. Required hardware:...

... rear shock tower is the same left to right. The other ones are labeled for passenger or driver. I also designed these to fit scrambler tires on both vehicles. For the lower shock mount, I just reused the lowers off of the original SCX24 shocks.

Don't try to rotate or flip, that doesn't work :) I find that it's best to drill out the shock mounting holes to 2,5mm, it's not easy to print small holes accurately. ... Use at least three walls +bott/top layers for rigidity, that is better than high...

This is a set of upper shock mounts for putting Carisma shocks on an SCX24 deadbolt or C10. I used M1.4x6mm screws to give it a little extra grip vs the factory M1.4x5mm, but the shorter screws would probably work. Carisma shocks bolt straight into...

### Printing Notes: 2 x `AxleShockAdapter.stl` 2 x `AxleShockAdapter_mirror.stl` ## BatteryPlatform Replacement for the stock battery platform with larger holes for mounting carisma shocks. Many (too many?) options, for you to adjust shock angle...

Français Support de Bavette arrière pour " TRX4 " Anglais Rear Bib Support for "TRX4"

this monut is for my jeep on an scx10 I fornt works great just waiting to print the back agian i made it to small the first time its 86mm tall from the scrow holes on the shock tower to the flatspot

body mounts to suit traxxas trx4 and 3d printed land rover discovery 1 and 2 bodies bolts to internal body structure and chassis rock slider mounts requires rear 313mm wheel base adjustment to suit (front axel in standard location multiple body...

Taller shock mounts to run Axial 90mm oil shocks or similar.

In addition to printing these parts, you will need the following Traxxas parts: 8080X (inner fenders with clipless mounts) 9216 (clipless body latches) 3931 (3x8 flat head screws) The inner fenders are installed on the chassis, replacing the original...

These lower shock mounts install on the stock Clod Buster gear case supports and allow for the installation of dual shocks per corner. These parts also incorporate a lift, so 100mm shocks can be used without clearance issues. Left and right hand...