ts100 stand 3d models

TS100 stand, requires a 608zz bearing (press fit)

... I made mine out of wood and aluminium but the base could be 3D printed. You can find the Fusion 360 file on my website [Miniproject 1](https://www.leosodergren.com/blog/evening-project-1-ts100-stand)

Yet another TS100 stand. This will only work with tmorris9`s guard https://www.thingiverse.com/thing:2864038 which I highly recommend to all TS100 users. Due to this guard demands no metal add-ons. ... Any filament, 0.3 mm layer height, 20-30%...

Yet another TS100 stand. This will only work with tmorris9`s guard https://www.thingiverse.com/thing:2864038 which I highly recommend to all TS100 users. Due to this guard demands no metal add-ons. ...Any filament, 0.3 mm layer height, 20-30% infill,...

This is a remix of the TS100 stand by Patrovite (thanks). Instead of a metal washer to rest the soldering iron against I used a copper 22mm to 15mm pipe reducer from my box of plumbing supplies. It works pretty well. It is easier to place the iron...

I wanted a stand for my TS100 that would hold it firmly and have a place to put some a brass sponge for cleaning. This one fits the small kind of brass sponge, roughly 58mm cup. You could put the sponge directly in there as well. Using 1.5mm wire...

I wanted a stand for my TS100. Simple design with space for a sponge. Utilizes 22mm bearings for the business end of the iron. Drawn up of FreeCAD, sliced in Cura, printed on an Ender3 S1 Pro using generic PLA. ...I used 5% infill with no issues.

Yet another stand for the famous TS100 soldering iron. It uses two large washers (outside diameters 30mm and 24mm, 2mm thick) to hold the hot bits of the iron. The base is glued to the main body of the stand. I filled it with sand to give it some...

Holds TS100 soldering iron by the handle. ...Firm enough to screw to a wall

Juste a simple add of a space for MINI t-stand. ... For more informations please look the original project : https://www.thingiverse.com/thing:3495809 Best, Franck

You need 1 additional washer with 2mm thickness and 25mm Diameter.Optional, put some weight under the holder, to ensure that it has a good stand. 

A variant of the TS100 stand by [nuverian](https://www.thingiverse.com/thing:3461009) but with (almost) no bridging requirements. ... Just a few quick modifications done in Tinkercad...

paper clip 100x24x1.80 mm

A stand for The Miniware TS100 soldering iron. Use standard 8 x 22 x 7 mm bearing in the center as a heat shield. Found in skateboards. Use M12 nuts and bolts in the back as a weight. ...https://www.youtube.com/watch?v=HgrB5P-rDLw...

From the other side of the stand there is a coaxial silicone cable that has 5525 connector at the end, which I connect to the TS100. In this configuration the TS100 can be connected all the time and when I need it I just take it and the accelrometer...

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it. After forming the end can be cut with a hacksaw to make...

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it. After forming the end can be cut with a hacksaw to make...

This is a form to bend a 2.5-3mm wire into a coil as a stand for a ts100 or similar soldering iron. I used a cloths hanger, but sanded the paint off first so the hot iron wouldn't burn it.</p> <p>After forming the end can be cut with a hacksaw to...

This is a tool holder that was made to hold the TS100 soldering iron and ES120 powered screwdriver. I created this because these awesome tools were sitting on a table and deserved better! I added some material to the inside to prevent any...

Remixed this to be able to use a 608 bearing, glued in place with super glue.

Uses American pennies for weight. ...Coins around 19mm should work just as well.

This is stand for the TS100. It's designed to sit in a TS100 case under the iron. When attaching to the soldering iron slide it down the shaft dont try forcing it through the cut out in the hole. You can solder with the stand attached without it...

This stand is printable without support ! i used 3-pin JST SM connectors to the ts100. ... and a flat plug male connector to the battery

Put Skateboard bearings in the grooves to act as a heat isolator Put some Sand or something heavy inside the bottom and close it by glueing the bottom lid on.

This stand is printable without support ! i used XT60 connectors to the ts100. ... and a flat plug male connector to the battery

This stand is for the **TS100** soldering iron. I included a tip cleaner. The washer is 26.5mm in diameter and it's tickness is 2.5mm. It can be adjusted in the source file. I used Openscad 15.03 to design this object. Source code in the "Thing...

My alternate design for the ts100 soldering iron holder for the tiny e-lab modular system. ...Made to fit the following brass wool holder: https://www.amazon.com/dp/B08FQBS97L

This stand is simple and useful, but the design is not totally friendly for 3D printing. http://www.thingiverse.com/thing:3598559 The designer made a 3 degree bend in the part. This part angles the soldering iron so that the tip sits higher off...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

The original by vtrman does not have a big enough holder for the brass wool. This one will fit most dish scrubbers too. Added a small hole next to where the iron sits for the allen key. You will need - one inch washer x1 - one and a...