turnigy lipo battery 3d models
76020 3d models found related to turnigy lipo battery.
thingiverse
This is a case for a Turnigy Nano-tech 1500mha lipo battery. Since I'm still learning, sometimes I have really bad crashes... I've destroyed one Nano-tech and cut at least two balancer plugs. Since some of my batteries are scratched and have some...
grabcad
nano-tech Turnigy LiPo 1600 mAh battery with JST connector. MPX included in assembly was the ones that I find on this site (credits to the owners). Connectors are not attached to be easy to remove them as you need. ...Feel free to use it for...
thingiverse
A holder/mount for the Turnigy High Capacity 6600mAh 6S 12C Lipo Pack. This can be used to just hold the pack on a wall, or to mount it to a device that you're using it on - I use it like this for my electric conversion mower. Its not a tight fit...
thingiverse
Battery tray to hold down a Turnigy 3s 2200 lipo I am sure that other makes of 2200 3s batterys will fit and I purposefully made the design a bit slack to allow for puffed cells Can always add thin foam pads I have printed off and built parts to make...
thingiverse
this is just a simple case to protect the 6s multistar 16 ah lipo battery from stress (inside the frame or bag etc) while riding your ebike. it is best to put additional "thin" foams around the battery to be more efficient. remember it does not...
cults3d
I use these batteries to replace my old drill NiCads : https://hobbyking.com/en_us/turnigy-nano-tech-1300mah-4s-45-90c-lipo-pack.html Make sure you also use somthing like this to cut off the battery before it goes under voltage :...
thingiverse
I use these batteries to replace my old drill NiCads : https://hobbyking.com/en_us/turnigy-nano-tech-1300mah-4s-45-90c-lipo-pack.html ---------------------------------------------------------- Make sure you also use somthing like this to cut off the...
thingiverse
... version of http://www.thingiverse.com/thing:761361 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=761361 Instructions Using the following options: battery_width = 36 include_strap_tab = Yes battery_height = 26
grabcad
... Model with top and side labels. ...Great to model your Radio Control Multicopters, Quadcopters, Hexapods, Cars, Boats and Planes. * If someone wants to add the bottom label as my batteries all have vercro glued to them so I can't scan the label.
grabcad
... Model with top and side labels. ... Great to model your Radio Control Multicopters, Quadcopters, Hexapods, Cars, Boats and Planes. * If someone wants to add the bottom label as my batteries all have vercro glued to them so I can't scan the label.
thingiverse
Remake of pintokitkat's battery holder. ...This remix holds a Turnigy 2.2 3C battery. ...I am using it on my Hobby king Q450 quad-copter.
grabcad
Turnigy Nano-Tech 2200mah 4S 25~50C Lipo Battery PackDim: 100,5 X 32 X 35
grabcad
Uses dimensions listed from HobbyKing.Length-A (mm) 147.00Height-B (mm) 67.00Width-C (mm) 51.00
thingiverse
Customized version of http://www.thingiverse.com/thing:348618 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=348618
thingiverse
I've taken an old 2.2 Amp 7,4v Turnigy LIPO battery (104x35x16) and searched for the best lowest place to the battery. Lid has some hooks around to use elastic rubbers to keep fixed the battery, but also a couple of pillars to place a lid locked by...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=873062 Instructions Using the following options: thick_edge = 0 battery_length = 105 sunk_screws = 0 mb_hole_distance_length = 115 mount_basis_thickness = 2 mount_basis_width = 58 battery_height...
thingiverse
Battery tray for HK X525 frame. ...Designed for 3300mah 45C 3S Turnigy LiPo battery but should fit any battery with similar dimensions. ... Prevents your battery from wiggling and slipping out of the velcro strap.
thingiverse
Size: Battery length = 145mm Battery height = 25mm Battery width = 53mm hole distance length = 110mm hole distance width = 70mm fits for this Battery: https://hobbyking.com/de_de/turnigy-5000mah-3s-20c-lipo-pack-xt-90.html
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=348618 Instructions Using the following options: hole = 3 battery_height = 32 hole_distance = 50 battery_length = 165 wall_height = 1.5 band_hole = 1 battery_width = 52 light = 1 cable_tie_hole...
grabcad
2200mAh, 3 cell, LiPo. widely used in remote controlled model aircraft, cars, etc. Fitted with EC3 power and JST ballance connectors, see my seperate models. ...The leads and connectors are arranged to suit a model helicopter I am designing but can...
thingiverse
Case to store 5x Turnigy Nanotech 2S 300mah 45-90c lipos.