valve index frunk 3d models
30387 3d models found related to valve index frunk.thingiverse
Lightweight 2x 40x10mm fan mod for Valve Index frunk. ... 2x 40x10mm 5v fans 8 x m3 skrews and nuts USB plug
thingiverse
This is the exact same as the Valve Index Frunk Fan by Maxxgold but it has pegs so that the fans snap fit in. ...It also has pegs for the switch so you can glue it in.
thingiverse
Just the open sourced STP file from Valve's github about the Index hardware, converted to STL for your convenience.
thingiverse
Easily placed on the front of a Valve Index to enable a very small amount of airflow through the VR headset. There is not enough air moved to dry your eyes, but just enough air is moved through the headset to keep your headset from fogging up,...
thingiverse
A mount that fit inside index's frunk 4 designs available Frame, Frame without vent cutout. Covered, Covered without vent cutout. ... Not yet tested Step files available for modify to fit your own gadgets
thingiverse
STP file from Valve's github about the Index hardware https://github.com/ValveSoftware/IndexHardware, Made hole for chilldex https://chilldex.com/ and converted to STL. ...
thingiverse
I saw on Reddit a couple of people mounting fans to their Index not in the middle but on the sides where the vents are, so I took that idea and created this mod. The fans are exposed so you can choose tho have them be 40x40x10 or 40x40x20. V1 has...
thingiverse
Everything fits great, i just wanted to get this out there for everybody. ill update with more details later. almost forgot you will have to remove a small foam peg that's on the circuit board otherwise it will interfere with the fan blade's I used...
thingiverse
Slot-in Stereo IR 170 Evaluation Kit frunk mount for Valve Index VR headset https://www.ultraleap.com/product/stereo-ir-170/ Notes: -Prints without supports -Design has small tabs that hook into frunk vents, verify these features print properly.
thingiverse
This replaces the frunk, so you will need to unscrew the front of the Index before installing this (using the same screws). Be careful with the exposed PCB. I bought two 5V noctua fans and soldered the cables to a male USB. The cables and usb are...
thingiverse
... it's too tall. I only used heat shrink tubes to insulate the connectors. I recommend unscrewing the Index's main cover plate and drill holes in it as shown on the photo. This greatly improves cooling even when not using the frunk fans at all. ...
thingiverse
one stl has the displays parallel to the bottom of the frunk pocket. the other has the displays angled to match the face plate. the stock magnetic face cover fits over both. I plan on using an Arduino Nano to drive the Displays. have not had the...
thingiverse
Easily placed on the front of a Valve Index to enable a very small amount of airflow through the VR headset." - Maxxgold My Remix extends the original 40mm by a switch. It is a mystery to me how to use this without a switch, so I made a remix on the...
thingiverse
This is a new low poly cover for the Valve Index Headset. It can be usefull if you do not want to scratch the original one, by bumping you controller into it (for example). I made a version without holes, for those like me who are bothered by the...
thingiverse
Frunk Mod to attach the naked Stereo 170 sensor to a Valve Index
thingiverse
... is incorrect. ... Specifically, it doesn't take into account the front, right, upper sensor on the Valve index headset. ... I've adjusted the Frunk Exhaust Enclosure to account for that sensor and scaled it up a tiny bit to fit better.
thingiverse
Just push the print into the Index's Frunk to secure it! You will not need any tape. To actually _connect_ the facial tracker, you will need a **`USB Type-C Female to USB Type-A Male`** adaptor. # Note This mount will not hold up...
prusaprinters
<p>A remix based off of <a href="https://www.thingiverse.com/thing:4552259/files">RandomMode's dual fan design</a></p><p>I used their model files to create a single fan variant, as I didn't want to use two fans. This model also includes a slot for a...
thingiverse
I didn't make this. ...Feilen over at the VRCfacetracking discord is the mastermind behind this creation.
thingiverse
Don't have time to type a proper description at the moment I'll add one soon hopefully! ... I explain the main differences in the video below ^^ Link to the usb adapter I used:amzn.to/3qRZ4km
thingiverse
This thing allows you to mount a fan on the Valve index, to replace the frunk part on the front and to use the USB plug. This will help to pull out warm air from inside of the headset, not necessarily to cool down components but to prevent it from...
thingiverse
**I do sell the finished product on my Etsy store!https://www.etsy.com/uk/listing/1047496097/valve-index-dual-fan-frunk-mod-set?ref=shop_home_active_1** Before you continue please read: I am not responsible for any damages that could occur from bad...
thingiverse
... I find it really hard to appreciate VR during summer : the headset is a little bit warm and the air inside isn't moving. So I made this mod in order to add two 40mm fans, on a 3D printed part that replaces the original "frunk" part.
thingiverse
A simple visor derived from the official Index CAD models, made so mods can be easily screwed on in different positions. ...The holes will take M3 or 4-40 screws, so as long as they're shorter than 5mm.
thingiverse
https://www.etsy.com/uk/listing/1065848597/valve-index-minifan-dual-fans-frunk-mod?ref=shop_home_active_1&frs=1** Before you continue please read: I am not responsible for any damages that could occur from bad wiring/soldering, I use my fan mod daily...
prusaprinters
I imported the model from Valve's official 3D Files into PrusaSlicer. ...I was suprised that this model wasn't already uploaded so people could print spares!<br><br>(My logo on the front is just a sticker, not part of the model)</p><p><a...
thingiverse
I modified the version with the holes filled to add two tiny switches. I used one to turn the fans on and off, and the other to switch them between a high and low speed. This was accomplished via a linear voltage regulator that steps the voltage down...
thingiverse
Might find time later to tweak the mount's placement (college is taking all of my time lately) You will need to get yourself and/or print: - 1x Valve Index Frunk mount (the main item in this thing) - 1x Slider (also included here) - 3x Mount...
thingiverse
This is an adapter to connect the Vive Face Tracker to the Valve Index Frunk, you will need 1x M3 screw and nut to secure the tracker to this print.