vs4 10 3d models
329376 3d models found related to vs4 10.
cults3d
Dimmer/receiver plate for Vanquish VS4-10. ...To be placed on the right side under the passenger seat (DIG side) see picture if needed 2 files to print cover with logo too fragile so I opted for a simple but effective cover.
thingiverse
Head light bucket for the VS4-10. Uses 3 5mm leds in each housing. Bolts up to existing holes using factory hardware. I wired 3 leds in series with 120Ohm resistor and supplied it with 12v. Use this wizard if you use a different supply voltage.
thingiverse
A rear corner plate protector for the Pheonix VS4-10. Mirror the plate with your slicer for the opposite corner on the small bumpers. Free to Print and Share or sell. Tips are always great. ... https://www.paypal.com/paypalme/Greensap
thingiverse
This is a receiver box for the Vanquish VS4-10 pro, though it may work on the limited and ultra as well though I have not tested those. Its a big box and was able to fit my receive and the excess wiring. to fasten the lid down you will need two...
thingiverse
This is a rack for the Vanquish VS4-10 Phoenix scale crawler. Mounts with the included clips to mount the bed sides or to the bed sides directly. I used super jumbo popsicle sticks for the wood slats and hit them with a brown wash. I have included...
thingiverse
RC4WD 4Runner Body can be mounted onto the VS4-10 Chassis with these simple brackets.
cults3d
rc gang 93 Conductor + seat head rests with beard for RC CRAWLER VANQUISH VS4 10 adaptable on other RCs 83x72x51 mm
thingiverse
You can use this easy to print part to mount an ESC next to the steering servo on the Vanquish VS4-10 RC Crawler.
thingiverse
This is an additional brace for the inner fenders for a VS4-10. This is useful if you have cracked the lexan around the front mount. ... Use the servo space if you do not have a servo winch installed.
thingiverse
Battery tray to be placed on the left skidplate of any VS4-10 platform. It can securely house a full (145mm) or short pack (ca. ...110mm) with use of the velcro strap from the kit
cults3d
Battery tray to be placed on the left skidplate of any VS4-10 platform. It can securely house a full (145mm) or short pack (ca. ...110mm) with use of the velcro strap from the kit
thingiverse
Body mount brace for the Vanquish VS4-10. There is a short version and a tall version, use the short up front and the tall in the rear (for SUV bodies). ... Requires 2 screw pins, m3 for the small brace m4 for the tall brace.
thingiverse
I had 2 fenders on my VS4-10 snap where they are bolted to the chassis with 2 bolt next to each other, near the bumpers. Maybe I screwed them in too tight. These washers are supposed to reinforce that area. Print 4, one for each corner of your...
myminifactory
A side mirror for the Vanquish VS4-10.This should fit all bodies.Should fit a lot of other bodies for your scale rock crawlers. ... Designed to print without support.Glues to your body, no holes required.For the reflective surface I like using aluminium...
prusaprinters
A small and simple side mirror for your VS4-10, or other RC bodies. Prints flat on its face, no supports needed. I printed this in TPU so it flexes instead of breaking. ...Stick on a circle of aluminium tape or tin foil for the full effect.</p> <p>This...
thingiverse
A small and simple side mirror for your VS4-10, or other RC bodies. Prints flat on its face, no supports needed. I printed this in TPU so it flexes instead of breaking. Stick on a circle of aluminium tape or tin foil for the full effect. ... This is...
myminifactory
The VP20002 VS4-10 PRO Roll Cage has been designed as a direct fit to the Vanquish Products VS4-10 PRO and ULTRA kits. ... The rolll cage bolts to the interior tray with four M2.6x5mm screws (sold seperately).
myminifactory
The VP20001 VS4-10 PRO Cab Cage has been designed as a direct fit to the Vanquish Products VS4-10 PRO and ULTRA kits. ... The rolll cage bolts to the interior tray with six M2.6x5mm screws (sold seperately).
cults3d
This grill has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA kits. ...The Grill bolts to the body with the stock screws.
cults3d
This grill has been designed as a direct fit to the Vanquish Products VS4-10 Origin, PRO and ULTRA kits. ...The Grill bolts to the body with the stock screws.
thingiverse
A license plate frame with light for you Vanquish Products VS4-10 Origin, Ultra or Pro body. Prints flat without supports. ... I like this tool for making plates: https://www.acme.com/licensemaker/ Print your plate, preferably on a laser printer,...
myminifactory
A license plate frame with light for you Vanquish Products VS4-10 Origin, Ultra or Pro body. Prints flat without supports.I like this tool for making plates:https://www.acme.com/licensemaker/Print your plate, preferably on a laser printer, and...
thingiverse
This is an inner fender brace for the VS4-10 Pro. It also adds 6mm of space inside the fuel cell to allow for more room for electronics. ... This will require screws that are 6mm longer for the fuel cell lid.
prusaprinters
A license plate frame with light for you Vanquish Products VS4-10 Origin, Ultra or Pro body. Prints flat without supports. I like this tool for making plates: https://www.acme.com/licensemaker/ Print your plate, preferably on a laser printer, and...
myminifactory
I had 2 fenders on my VS4-10 snap where they are bolted to the chassis with 2 bolt next to each other, near the bumpers.Maybe I screwed them in too tight, maybe it's a weak point in the design.These washers are supposed to reinforce that area.Print...
thingiverse
This is a Mamba X ESC mount for the Vanquish VS4-10 pro though it may work on the origin limited too. This can work with or without the aluminum top plate that's installed on top of the plastic slider trays. This mounts on the Driver side. The motor...