vw square back 3d models
208520 3d models found related to vw square back.thingiverse
Skull Vw Logo for the back of the car. ...Don't care about my dirty car :D Print Settings Printer Brand: FlashForge Printer: ...
thingiverse
a VW Beetle back window vent print settings : nuzzle: 0.4 layer height: 0.2 material: abs
thingiverse
Customized version of https://www.thingiverse.com/thing:3076526 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3076526
thingiverse
All I wanted was a nice big back case to put on the back of my NTC Pocket Chip. The designs I was able to find are mostly broken and unprintable. I put in a bit of time designing this and making sure it works, so hopefully it is helpful to someone...
thingiverse
This is a holder part for a VW T4 with back drawers. Holds down the linear rails which carries the drawers. Print with 100% infill for best results. Width is 103mm height is 93mm. Halterung für einen VW T4 mit Heckauszügen. Hält die Schienen unten,...
thingiverse
Alhambra Handle, For adjusting Seat back position on a Seat Alhambra UPDATED FILES - CORRECT THIS TIME This works on a Seat Alhambra, Ford Galaxy or VW Sharan. Tried and tested. This is a replacement for - but not a direct copy of - VW Audi part...
thingiverse
Replacement for the VW emblem at the trunk of a T4 California. Dimensions are not 100% accurate yet, that´s why it is in "work in progress" status. ... Further logo variations to follow.
thingiverse
I adjusted the VW logo file from here https://www.thingiverse.com/thing:3027546 To make a knob to fit our seats in our T4 camper that were missing when we bought it. I printed them on my Adventure 4 with silk grey PLA on basic settings. Hope this...
thingiverse
This got me thinking how I could use these in our VW T5 Campervan. So I designed a bracket that will slip onto the head-rest struts and allow a carabiner to be attached. These can then be used to ahng just about anything you like in the van. ...
thingiverse
I had lost the little square that is sitting at the back of the Windex that are made by Davis. so I draw one from original. ...it fits just fine
sketchfab
118 Eaton Square London https://www.atd.london/architecture/eaton-square Architectural Section Model
prusaprinters
This aid makes it clear where the boundaries are when shooting Instax Square on RB67.Printed in Polycarbonate for strength and durability.Layer height: first layer 0.2mm, succeeding layers 0.05mmTemp: 225 (Polymaker PC-MAX)Bed: 100Nozzle: 0.4mm
thingiverse
Modified it to take the breadboard from the top, and to have a solid back (so the kids don't get to play with the double-sided tape already applied. Also moved the Arduino mount down 3mm so that the USB port is not sticking out allowing for...
thingiverse
Customized version of https://www.thingiverse.com/thing:3076526 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3076526
thingiverse
... an die Fächer (https://www.thingiverse.com/thing:5556200) ran zukommen. ... -------------- A support to hold the back seat of the VW T5 / T6 open to be able to work underneath or to get to the compartments (https://www.thingiverse.com/thing:5556200).
thingiverse
This is a remix of VW Vanagon Westfalia T3 Pop-Top Cookie Cutter by mishtevan https://www.thingiverse.com/thing:2773125 I simply cut out the back of the cookie cutter so it would be easier to pop out stubborn cookie dough. Printing it now and it's on...
thingiverse
Here is a little gadget for your VW T5 with one tailgate door. It allows the door too be locked but there will be a small gap for fresh air while ur sleeping in the car. Its very easy to print, if possible use some stronger materials. It fits for...
thingiverse
If a previous owner (or you) had hacked up/cut up the metal dash in your Beetle to put a DIN radio and you now want to put the stock radio back, you will find that the cut up /hacked up hole is too big and the stock radio does not cover the hole. You...
cgtrader
SQUARE BACK CANED ARM CHAIR by Bakerfurniture
thingiverse
It's a dowel pin, for square holes, the 10 mm, on the VAG group cars, i made it for my Skoda Fabia mK1
thingiverse
Anyone who knows these VW OEM wheels probably has either had the decorative plastic "bolts" break off or has accidentally destroyed a few. I'm still a fan of OEM wheels, so I decided to spruce mine up a bit since I was missing a few of the plastic...