wallet and key holder 3d models

Wall mounted wallet and key holder

Took the original wallet and key holder from x9x9x9x9x9 and added thicker hooks while making the dimensions fit my wallet. ...Also added a screw hole for easy mounting:)

Took the original wallet and key holder from x9x9x9x9x9 and added thicker hooks while making the dimensions fit my wallet. ...Also added a screw hole for easy mounting:)

More room for my wallet, a place to hold a pocket knife, and a way to screw it into the wall.

I made this little holder for my bi-fold wallet The inside dimensions are 95mm wide x 25mm thick x 65mm tall but height really doesn't matter. There are 2 different versions. I made this as a gift and hid a little adult message in the bottom for a...

Simple key and wallet holder! no support needed thanks to the triangle shape on the hook area all you need to do is go tinkercad and add your own drilling hole or modify it do credit tho if you do a remix thanks! ... i dont like holes on my wall so i...

... find one that really fit my usecase so I designed my own! ... This is designed for very slim wallets or money clips at or around 18mm. I used Scotch Extreme mounting tape to mount it to the wall. ... I hope this is as helpful to you as it is to me!

A remix. ...Simplified/removed suglass holder. ...added bigger hook for a backpack.

Geometric wallet and keys holder. Prints easily on any printer and mounts to the wall with screws. The pegs are made with a low tolerance - if they are too big after printing, just sand them down a bit. ...

I designed a wallet and keys holder that you can attach to the wall with command strips. ... Dimensions Outside: 130x50x35mm and the key holders stick out 15mm Inside: 120x40x35mm It takes about 6:30 hours to print Designed with Fusion360 It didn't...

Simple holder for wallet, keys and various stuff.

Wallet holder with a key holder attached. ... Printed in 2 parts so it uses no supports and with 4 different sizes of dowels for different interference fits.

My key fob is for a Nissan, and I'm not sure how it squares (or rounds, rather) up against other Nissan or other car keys but the cylinder I used for the hold was 37.5x20x75cm (LxWxH). The section for the wallet, or anything else, is 95x45x65cm,...

My key fob is for a Nissan, and I'm not sure how it squares (or rounds, rather) up against other Nissan or other car keys but the cylinder I used for the hold was 37.5x20x75cm (LxWxH). The section for the wallet, or anything else, is 95x45x65cm,...

Self-designed in order to keep my keys and wallet tidy in a corner. It can hold up to 7 pounds of weight comfortably. Great for sharing as well with the various hooks and stackable wallet support. ...I hope everyone can enjoy it as much as I do every...

Remix of the excellent Ridge Wallet Airtag holder, expanded to accommodate a key. ...Shown here holding a Shlage house key.Printed with PETG for higher heat resistance, likely works fine with PLA or other materials as well.

I've designed a wallet and keys holder for my desk, it holds a wallet, hangs up to four keys and has a small shelf. See the pictures for dimensions, my wallet is quite thick so it should fit several people. There are two holes to screw the holder...

This print could be screwed on the wall to hold your wallet, keys and coins. Wallet size should be within 40mm thickness and 115mm length. ...

Wall mounted wallet, keys, sunglasses holder thing to keep some of my crap together. Mine fits a regular bi-fold, ridge wallet, keys and sunglasses. ...Probably not for everyone, but I've included the .f3d in case you want to adjust to your needs.

Wall mounted wallet, keys, sunglasses holder thing to keep some of my crap together. Mine fits a regular bi-fold, ridge wallet, keys and sunglasses. ...Probably not for everyone, but I've included the .f3d in case you want to adjust to your needs.</p>...

This is a wall mountable key holder with three hooks and a slot at the top for a thin wallet (fits up to 3.75" wide, 0.75" thick). ...I haven't lost my keys since :) Instructions Prints easily via ABS, small enough that only minor warping occurred on my...

A printable key and wallet holder so you don't misplace either. The front plate slides into the base for easy cleaning when it gets full of debris. No supports needed if you print it correctly with the flat side down. ...

Added a second shelf and hooks on the sides for sunglasses to go in. ...It has screw holes, but I use command strips

At the current era, women have pockets that are getting *smaller and smaller*, until they become **nonexistent!** This is meant to be a holder for a phone, wallet, and keys.

To create order, everything must have a dedicated place. ...And this is the place where my wallet and keys belong to. ... The slit for the wallet is 139mm wide.

I scaled it to 5x and printed it but the mounting holes were way too large. I brought it into Autodesk 123d and plugged the mounting holes. This version can be affixed with double stick tape or mounting holes drilled out as you see fit. ...

My wallet, phone, keys and belt. What more does a guy need? I print these with no support, you may want to check if that will work for you. Attach with command strips or VHB double sided tape. Adam Sandler needs one! (see video..) ...

Adds a spot to hold the knife instead of coins and makes the key hooks smoother. ... Also adds two keyholes to hook onto a drywall anchor and screw.

All the things you need when leaving your home ready to go! ... A Shelf for your wallet and magnetic holders for two sets of keys. The design has compartments for magnets with a diameter of 10mm max. Blender file included. ...

I needed a place to put my wallet and keys next to my door. Found and remixed one with hooks and added a plate. ... My wallet is 75mmx100mm and fits perfectly in the cup but it could hold any size really.