watercooling 3d models
365 3d models found related to watercooling.thingiverse
SUPPORT POUR NF WATERCOOLING HOTEND JE PEUX MODIFIER AU BESOIN SUPPORT POUR FAN30X30X10 N'HESITEZ PAS A DEMANDER
thingiverse
Needed to upgrade watercooling setup for couple of my PCs and thought that why not design my own reservoir? So this is the first design and I printed couple of these using PETG and Filaflex for gaskets. Designed for immersive pump, Im using Eheim...
prusaprinters
... hot glue, but not sure if it's a good long term solution. Some kind of silicone might work better.</li> </ul> <h3>How I Designed This</h3> <p>OpenSCAD. Source here: https://github.com/spegelius/3DModels/tree/master/Watercooling Category: Computer
thingiverse
Mount a 50mm diameter watercooling reservoir to a 12cm fan mounting holes.
thingiverse
Voici mon design de reservoir pour watercooling imprimé en 3D, il peut bien sûr étre utilisé pour d'autres applications. Les raccords dispo sont compatibles avec les tuyaux de diamétre 10mm interne. This is my DIY watercooling reservoir made using...
grabcad
Various Standard Watercooling Fittings. Modeled off Bitspower Components. Right Angle Male-female Male to Male adapter Male to Male Short adapter Female to Female Adapter 3/8" (10mm) ID Compression Fitting. ...Standard G1/4" Through Port
thingiverse
This is the support for the reservoir of my DIY watercooling project, it's made to be install on the 5,25" bays in the front of a computer case.
thingiverse
This insert replicates the EK ABS inserts that prevent PETG tubing from buckling under load and becoming loose in watercooling fittings. PETG can warp around 50 to 60 C which watercooling temps will exceed, especially after leaving GPU. This can...
youmagine
This designs are about my Hackintosh which I built. ...These parts are for the aquacomputer filter and the EK-XRES 140 Revo D5 PWM reservoir and pump unit for my watercooling system. ... the full project is on my page: http://s-technologies.eu
thingiverse
Autant je peux faire des choses jusqu'à réussir comme pour ce watercooling autant je peux vite lâcher l'affaire quand il s'agit de chercher une info sur le net... Le fichier test sert à vérifier si vos impressions et le collage au sillicone sont...
thingiverse
En plus des piéces 3D il vous faut : 8 vis M4 25mm + rondelles 1 moteur cc 30 diamétre 30mm ------------------------------------------------------------------------------------------------------------------------ Here is my desing for a watercooling...
prusaprinters
I hated the double sided Corsair watercooling mount for the pump so I designed a cleaner looking mount.This mount is designed to be a direct swap for the Corsair mount. You will need 4 3mm nuts and 4 3mm x 10mm long screws to mount to the Corsair fan...
thingiverse
It is built for his nitropowered rc crawler so he could use a boatengine with watercooling. The tank has a slot on one side so a pump can slide right in. This is the waterpump used in this project: http://www.ebay.co.uk/itm/191797119322 Print...
thingiverse
My friend wanted to install a watercooling in a Silverstone FT03 Mini (http://www.silverstonetek.com/product.php?pid=333) but he has not handler to fix the pump...
thingiverse
Rc boat 36mm watercooling jacket. ...A bit tricky to instal the seals but very sturdy with enough tollerance to fit any 36mm motor.
grabcad
My first design, a watercooling custom reservoir representing the World of Tanks Logo, will be used in a thematic PC build.
grabcad
AlphaCool NexXxos XT45 420mm Radiator Has a minor error with the fins. ...Internals are modeled for fluid flow simulation capability
thingiverse
Trichter zum befüllen des Kühlsystems für Computer Wasserkühlung. Der Trichter passt in den Ausgleichsbehälter. Durchmesser unten 11mm Oben 50mm. Gesamthöhe 65mm Funnel for filling the cooling system for computer water cooling. The funnel...
thingiverse
Adapter to install a 120mm in a case without place. ... It take place of 4 x 5.25 rack
thingiverse
I made these clips for my PC, as u can see in the pictures. I wanted to organize the tubes a bit better as using straps. All made of PLA, printing time around 20 minutes for all. The clip for 4 tubes has one side with bigger clips, because the...
thingiverse
Customized version of http://www.thingiverse.com/thing:44850 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44850 Instructions Using the following options: cone2_max...
thingiverse
This is a PC Watercooling reservoir holder with a diameter of 50mm. It is designed to be used with a countersunk M4x16mm screw. It is meant to be mounted in a M4 thread, in my case on the side of the 5,25 Inch Bay of my Lian Li PC A70 Case. Of...
thingiverse
Modified Rennwaffen´s Super-Light Effector to fit a Volcano Heatblock and a water cooled Heatsink (i used this Instruction and fitted it to my needs: https://datdiy.wordpress.com/2019/09/01/e3d-v6-watercooling-mod-on-a-hypercube-3d-printer/ ). ... The...
thingiverse
Make sure you properly test you watercooling for leaks before connecting up your LED's. This tube is 100mm long only and to make longer covers you would need to join multiple together in a 3D editing program. I have included the original blender file...
thingiverse
After reading a lot of informations there: https://well-engineered.net/index.php/en/86-community-water-cooling https://www.thingiverse.com/thing:247599 http://forums.reprap.org/read.php?336,765316...
thingiverse
https://www.youtube.com/watch?v=xmUUiaYRNKc https://hackaday.io/project/177832-led-watercooling-modules