wrapmaster wrapping paper cutter 3d models

simple wrapping paper cutter that uses a utility blade I would suggest use of WPC-03 or WPC-04

Wrapping paper cutter that keeps your paper from rolling off the table and cuts better then others that I have tried. ... It uses regular straight razor blades.

A remix of the popular Wrapping paper cutter for the holidays. Requires a X-ACTO #11 blade. ... https://techbytes.ca/3dprints/ Hope you all enjoy.

A quick cutter tool for wrapping paper tubes. Works with thin razor blades. The curve of the slot keeps the blade in place. the holes in model keep it able to flex. ...Feed wrapping paper in the beveled opening and slide tube through to cut.

Made a simple grip that prints in TPU that is glued onto a paper wrapping cutter (https://www.thingiverse.com/thing:3226136) to help make it more reliable and helps stop the paper from clumping up on the cutter.

... after test. -------------- Wrapping Paper Cutter. Add an exacto blade within the wedge with blade facing away from the opening. Put your tube of paper in and run the wrapping paper cutter down to make the cut. ... Not an original design.

Wrapping paper cutter for easy paper cutting. This is better than bothering with scissors. Model is programmed for a 9mm wide knife. ...→ <a...

This is a tool for cutting wrapping paper I may upload one for vase mode soon

A remix of the popular Wrapping paper cutter for the holidays. ...Requires a X-ACTO #11 blade.</p><p><a href="https://techbytes.ca/3dprints/">https://techbytes.ca/3dprints/</a></p><p>Hope you all enjoy.</p><h3>Print...

Wrapping Paper Cutter MK 1 works perfectly if you 'jam' the blade into position... I managed to do this with a thin elastic band... I cut the band then placed it over the slot... grabbing the scalpel blade with a long thin nosed pliers, I then pushed...

Remixed the original cutter so that you can slide cutter blades from the bottom. Pressure of the tube holds the blades in place while cutting any tube of paper. ...It uses a 18mm utility snap off blade, ( <a...

Following a little storm on a 3D printing Facebook group, here is my version of a slide cutter for Christmas paper. more info to follow.. and more photos etc... I have just added a detail view, of where the scalpel blade will fit. ... It was...

This is a remix of the Wrapping Paper Cutter (X-Acto #11 Version) found here: https://www.thingiverse.com/thing:3226136 I loved the christmas tree one, so I wanted to do some other holiday shapes! ...Here are the files for a snowman, candy cane, and...

A wrapping paper cutter using single edge blades. Original was printed with 4 perimeters, but it can be printed with 30-50% infill. Support is required on the body for the overhang on the upper lid guide. User assumes responsibility for the safe...

There are two sizes - 51mm diameter and 60mm diameter so you can fit the larger rolls of wrapping paper.

My take on the wrapper holder/cutter. Designed from bottom up but not my original idea.</p> <p>This one is slimmer and more handy on the rolls i have come across. Being both thinner in diameter and wall thickness its also a bit cheaper to print en...

My take on the wrapper holder/cutter. Designed from bottom up but not my original idea. This one is slimmer and more handy on the rolls i have come across. Being both thinner in diameter and wall thickness its also a bit cheaper to print en mass...

Created this wrapping paper cutter for larger sized wrapping paper rolls (70mm) but can also work on smaller sized rolls. This uses X-Acto #11 blades. There are several options for logos for the outside: NoLogo, SnowFlake, Snowman, ChristmasTree,...

... All can be printed without any supports. I have seen any comments / post regarding that similar wrapping paper cutters do not work or break. I myself googled 'Little ELF' and watch the instructional video on how to use a similar product. ...

... rolls. Requested by a customer, so I thought I would upload it as well. Original is 60mm ID, which should be fine for 90% of wrapping paper rolls. ... Edit3: Added a PLA version that is currently untested to help with layer adhesion issues.

This is a handheld version of my other design for the wrapping paper slicer with a utility blade. This does not require and hardware and allows the blade to be replaced. ...Insert a pencil on the release button to allow the parts to slide apart.

This should fit all wrapping paper sizes and will save on print time! EDIT 2: Check out: https://www.thingiverse.com/thing:5161220 for a smaller version yet. This is a new design based on the first. I did some playing with the shaping of the...

Here is the minimal version with update for using two X-Acto blades.

The original of this was too big for me so I made a smaller, thinner version which still fits 10A Blades. ... Theres really nothing important to note when printing, its basically a circle

<p>Remixed (from scratch) for a standard, X-ACTO #11 blade.</p> <p>See here for a minimal version...</p> <p><a href="https://www.thingiverse.com/thing:3183256">https://www.thingiverse.com/thing:3183256</a></p> <h3>Print Settings</h3>...

<p>WHAT YOU NEED: 4 M3 x 8mm cap head screws; 4 M3 nuts; 1 regular razor blade<br><br>ASSEMBLY: make sure all printed holes and countersinks are clear and free of strings, pressfit the nuts into the printed fittings (use a soldering iron if needed),...

Another remix for a minimalist version. ...Still uses an X-ACTO #11 blade.

Thanks to the original designer, I have made this variant compatible with the 10 Blade and included a test print so you can be assured the blade will fit before wasting a 4 hour print! ... Quick video of it in action here https://youtu.be/kcgcOXJhJ5o

added snowflake patterns