xbox controller holder for desk 3d models

I wanted a way to store my Xbox controller right under my desk, a hands reach away. Screw holes are available for permanent attachment but I used a command strip and it holds just fine. As for taking the controller in and out, I thought I designed it...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

may need to flip the holder up right to fit the plate

Xbox360, Xbox One and Steam Controller controller holder for BILLY bookcase and JERKER desk, without screws. ...In order to adapt for Xbox One and Steam Controller just add the lip.

Fixed by MakePrintable

Fixed by MakePrintable

Fixed by MakePrintable

Fixed by MakePrintable

This is a desk holder for the controller clam grips, (also works for controllers without the grips). ... If people want one without the 'ears' so that you don't need to print with support or just aesthetically then let me know and I will upload a new...

... a few days after I printed it. ...This works very well so I am reuploading it here. Unfortunately I only downloaded the STL with mounting hole. Originally called "Under-Desk_Xbox_One_Controller_Holder_-_Sunken_Hole_Version_-_K_V_Design.stl"

My Under-Desk Xbox One Controller Holder stores your device in a practical yet aesthetically pleasing manner. I have also used this to store a Steam Controller to great success. I have used 3M command strips to hold this to the underside of my...

wanted a really simple under desk holder (for my Autonomous desk) to hold my Xbox One controller that is connected by Micro USB to my PC. Wanted it wide enough to hold the controller well, but also didn't want this to take hours to print. On my...

... after I printed it. ...This works very well so I am reuploading it here.</p> <p>Unfortunately I only downloaded the STL with mounting hole. Originally called "Under-Desk_Xbox_One_ControllerHolder-_Sunken_HoleVersion-_K_V_Design.stl" Category: Computer

This is a remix of the Xbox Control Holder by Aled4192. I closed the screwholes and used 3M tape to stick it to my desk. ...I also added the Logo.I just printed it with 10 % infill and printed it upright.

I wanted to save some desk space and made this to put my relocate my Xbox 360 Controllers over on the Fredde Desk rail. ... Ikea Fredde Desk https://www.ikea.com/us/en/catalog/products/50219044/?gclid=SubBass100onThingiverse

wanted a simple, quick to print holder for my controller, so made it. printed with 10% infill and 0.28, and stuck on with double sided tape (the 3M red kind), and it works pretty good. Does not fit the PS4 controller unfortunately. ...have fun!

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Designed up this dealer button to use in home games or have just as something laying around for any poker fan. It was inspired by a dealer button in Pokerstars VR. Printing: Ring - Infil to add weight, supports needed for spade inset. Letter...

Battery cover clip that can be used with phone holder from https://www.thingiverse.com/thing:2553522 Used for Xbox Android streaming setup

The only difference from the original file by rjrivera is that I made the section that clamps on the table shorter to mount on a thinner desk / table top than the original. Clamp is 20mm at the smallest point. ...All other measurements are the same as...

Just a simple mount that clings on to your desk and holds an xbox one controller below.

Remix combo of the following: Xbox one controller holder Mk 2 by Odemon: https://www.thingiverse.com/thing:1674704 and No-need-support Headphone Holder/Stand by hate_support: https://www.thingiverse.com/thing:3068725 I printed Odemon's controller...

Very simple controller stand that works with both Xbox 360 controllers and Xbox One controllers. ... Print Settings Printer Brand: Ultimaker ...

Xbox one controller holder for Ikea table thats 34mm thick

Needed to hook my Xbox controller over a 4mm glass door on my desk

Smartphone holder for the Xbox One controller. A 6.4x22.2mm spring (like in the picture) or a rubber band is required for proper operation. ... Have a nice use.

Xbox controller mount for the honecomb.Print the back on its side it doesnt need supports.print 2 of the pegs they needs two m4x12 screws with nut.&nbsp;&nbsp;Note:&nbsp;took the slope dims for this from chewbuggas wall mount they did that perfect.

56 magnet holes - 3mm diameter by 2mm depth Print with Supports @ 20% infill Should work with any xbox 360 or xbox One controller Easily attach your controller to your desk when not in use No GLUE REQUIRED!   Just push the magnets in!

This Hanger will accommodate several generations of controllers in both Xbox and Playstation flavor as well as handle most all headphones with wide or slim bands. It is very robust in feel and function. All models are printable with no supports,...