0 gauge jewelry 3d models

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: weight = 11 groove = 1 $fn = 50 margin = 12.5 type = 0 cursor = 100 diameter = 8 edges = 1

This is a configurable spacer for using between two large gauge earrings, to prevent them from pinching. ... It has been a life saver for my wife.

gauge 0.5 in

The first will add +1, +2, +3, +4 mm The second will add +5, +6, +7, +8 mm So the height-range is 14 till 31mm You can adjust the piston to the desired height by removing it, turn to the correct setting and remount it, then slide the gauge under the...

I wanted an height gauge that was solid, adjustable, not too flimsy for my 1/10th and 1/8th buggy's.It had to be easy to use, easy toi manipulate AND strong.The previous design ( https://www.thingiverse.com/thing:3704124 ) could use some improvement...

0-60PSI Pressure, oil, gas guage

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: weight = 11 $fn = 50 type = 0 edges = 1 cursor = 100 groove = 1 diameter = 8 margin = 0.1

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: margin = 0.1 edges = 1 diameter = 8 weight = 11 type = 1 cursor = 100 groove = 1 $fn = 50

Temperature gauge 0°-120° with G½’’ Thread

Ashcroft Gauge 0.500 NPT 0-100 PISG

Test gauge with 0.2 mm spacing between the walls.

Gap Gauge 0.5mm steps. ... Useful for bodywork on cars sheetmetal gap check over.

4" Diameter SS Pressure Gauge, 0-160 psi, 1/4" MNPT Center Back Connection, McMaster Carr P/N 4003K81

"Schwannenhals" bogie in gauge 0. ...Print at 50% for gauge H0 If you like my Designs, please considere leave a small tip or support me through patreon: https://www.patreon.com/kaito3d

42mm (15/8") pressure gauge

Coal crane in gauge 0. Its modeled like the coal crane that was used in BW Ottbergen (Germany). ...Print at 50% for gauge H0 (untested) If you like my Designs, please considere leave a small tip or support me through patreon:...

This design is for now only available on Cults: https://cults3d.com/de/modell-3d/verschiedene/db-umbauwagen-ab4yde-db-coach-ab4yge-spur-0-o-gauge-1-45-taskmodellbau This is a model of the german passenger car AB4yge. It was brought into service in...

An all inclusive Kill Team Gauge for the new Kill Team 2.0. Measurements are 1", 2", 3", and 6". Includes an empty design and a Tau design. Designed for printing on AnyCubic Photon resin printer. Not sure how this will print on an FDM...

An all inclusive Kill Team Gauge for the new Kill Team 2.0. Measurements are 1", 2", 3", and 6". Includes an empty design and a Tau design. Designed for printing on AnyCubic Photon resin printer. Not sure how this will print on an FDM printer. ...:)

Made a combat gauge for the orks. ...(Why should DKOKs be the only ones with a themed tool?) One side is also 4" (in case you play OnePageRules and have a slow unit :-D)

Radius Gauge If this designs helps you in any way, do you mind leaving me a quick tip via paypal? http://paypal.me/avicode Even the smallest donation helps support my effort in creating amazing 3D print designs for everyone. F3D also...

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: margin = 0.1 diameter = 8 type = 1 $fn = 100 weight = 11 edges = 1.5 cursor = 95 groove = 0.75

simple angle gauge 0-45 deg in 5 degree increments, made for use as a throw gauge for r/c airplanes

1.0 mm thickness feeler gauge 2.0 mm thickness feeler gauge 3.0 mm thickness feeler gauge 4.0 mm thickness feeler gauge 5.0 mm thickness feeler gauge 6.0 mm thickness feeler gauge 7.0 mm thickness feeler gauge 8.0 mm thickness feeler gauge 9.0 mm...

It utilizes two 3 x 6 x 2.5mm ball bearings stacked on each other (per gauge piece), and then the two plug pieces fit inside the bearings to make the held piece of the spinner. It isn't weighted on the edges, so it probably won't spin very well...

This is a Jewelry box inspired by the TARDIS in Doctor Who. Changed the door attachment to a pin and socket design instead of the hinges Some Assembly required with glue once the pieces are printed. ...Print List: TARDIS Sides X 1 TARDIS Top X 1...

Pressure Gauge 1/4" NPT 0-30 PISG

Version 2.0_bottom: As seen on ranger5g.com 52mm gauge fitment Factory OEM LOOK Prints on most printers (90mm x 60mm) Secure fit of your boost gauge retained air flow management (vent still works) Radiused vents for good air flow and visual look...

Simple combat gauge for Kill Team 2.0 (2021) cleaned up and pre-supported version available at https://cults3d.com/en/3d-model/game/kill-team-template-2-0-supported

Simple combat gauge for Kill Team 2.0 (2021) cleaned up and pre-supported version available at https://cults3d.com/en/3d-model/game/kill-team-template-2-0-supported