1 1 2 nut 3d models
1481279 3d models found related to 1 1 2 nut.thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Nut1 1/2" for sink drain The project was realized with tolerances for printing with ABS
pinshape
Summary Nut1 1/2" for sink drain The project was realized with tolerances for printing with ABS Print Settings Printer Brand: Zortrax Printer: Zortrax M200 Rafts: Yes Supports: Yes Resolution: 0.19 Infill: 90%-100%
thingiverse
This is a slip nut I made for my kitchen sink. ... It is equivalent to https://www.homedepot.com/p/Oatey-1-1-2-in-Sink-Drain-Pipe-Plastic-Slip-Joint-Nut-with-Rubber-Reducing-Washers-C2698C/205154062 though, notably, without the rubber washer. ...
thingiverse
Came up with this - which is split in two and can be screwed together so the collar runs inside the track, and the threads can connect to the underside of the sink, or any other standard 1 1/2" ABS plumbing pipe threads (black). Uses M3 bolts and...
thingiverse
... recessed in a custom enclosure. There was no room for channel locks, specialty spanner, nor a hammer and screwdriver (I'm not the one who designed the custom enclosure, lol). This made quick work of the nut and now I have a tool for future projects.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: inner_diameter = 8 nut_height = 6 head_diameter = 12 socket_facets = 6 facets = 6 nut_thread_step = 2 head_type = hex nut_diameter = 18...
thingiverse
This is an imperial 1/2" x 13 TPI by 1-1/4 inch long bolt and nut set with no overhang greater than 45 degrees. It is designed to mate with the nut of the same rolled thread. PLEASE REMEMBER THAT THIS IS JUST PLASTIC AND DOES NOT EXHIBIT THE...
thingiverse
I picked up everbilt 1000-049-738 1-1/2" Slip Joint Nut and washer kit and modeled the nut. Then when messing with firmware one my printer I needed something to print so I did. ...The threads look right, the hole is a little large but probably would...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:1562501 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1562501
thingiverse
Customized version of https://www.thingiverse.com/thing:1562501 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1562501
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: thickness = 2 nut_step_shape_degrees = 45 slot_width = 1 facets = 6 inner_diameter = 8 drive_type = socket step_shape_degrees = 45 nut_height =...
thingiverse
Nut SAE 1/2-20 1/2” tall. Threads are working perfectly. Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: type = nut resolution = 0.5 non_thread_diameter = 0 nut_height = 6 thread_length = 25 drive_diameter = 5 wing_ratio = 1 slot_depth = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: facets = 6 countersink = 2 inner_diameter = 8 slot_width = 1 drive_diameter = 5 thread_step = 2 head_type = hex slot_depth = 2 resolution = 0.5...
thingiverse
The picture shows the a 1/2 inch hose connector with original cap/nut in grey and the replacements in white, printed in PETG (but PLA would probably okay as well. For a real replacement print in grey color:-) For those of you who want to design...
thingiverse
Customized version of http://www.thingiverse.com/thing:156601 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=156601 Instructions Using the following options: size = 1/2
thingiverse
Nut to go on 1/2" PT thread or Pipe thread, found on various fittings like air and liquid hoses and pipes Instructions Made using "Nut Job" customizer: http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Using the following options:...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: screw_hole_diameter = 55 height = 20 knurled_density = 70 cross_section = 0 nut_sides = 6 bottom_thickness = 1.5 knurled_strong = 2 nut_thickness...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_thread_outer_diameter = 4.5 nut_step_shape_degrees = 45 thread_step = 2 inner_diameter = 8 nut_thread_step = 2 texture = exclude...
thingiverse
**Print the following:** * 1x spinner body (3x, 4x, or 5x) * 2x grips * 1x assembly jig The **1/2" nuts I used are 11.2mm tall**. The spinner body is 7mm high (to match the height of the 608 bearing) which leaves 4.2mm difference. ...The **assembly...
cults3d
Print the following: * 1x spinner body (3x, 4x, or 5x) * 2x grips * 1x assembly jig The 1/2" nuts I used are 11.2mm tall. The spinner body is 7mm high (to match the height of the 608 bearing) which leaves 4.2mm difference. ...The assembly jig is used...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: nut_resolution = 0.5 nut_step_shape_degrees = 45 nut_thread_step = 1.8 nut_thread_outer_diameter = 21.3 nut_diameter = 26 nut_type = normal...
thingiverse
In making rain barrels, I found I was getting leaks around the 1/2" NPT fittings (even though they were tapped and sealed) when things would warm-up in the sun. I decided the thin walls of the barrels weren't enough to keep things tight. So I...
thingiverse
Used for a half inch hex nut. ... Useful for any nut that needs to often be adjusted. ...Would also work on the head of a bolt.
thingiverse
... magnetic valves stoppt working because of broken plastic srew-nuts. ... I could not get this nuts as a plastic part. The supplier wanted to sell me the complete inlet with a nut for 60 Euro! ... So I printed some nuts to repair the magnetic valves.