1 1 4 hitch cover 3d models
1213399 3d models found related to 1 1 4 hitch cover.thingiverse
Scaled up original by Poguey44 to fit on my 1-1/4" Curt hitch with a Thicker Recieving end. ...Also made shaft longer to engage clips Class I Class II Hitch
thingiverse
This is a hitch cap for 1-1/4" hitch for your scion car. I added lot of holes to fit many models of hitch. I took this logo and enlarge it to fit on the cap: http://www.thingiverse.com/thing:783489 Print Settings Rafts: No ...
thingiverse
This is for a 1-1/4" square receiver hitch receiver. It slips in and wedges so it does not readily fall out yet you can pull it off when you want to use the receiver hitch. Instructions Print in a black material to match the existing hitch or your...
thingiverse
Here is a 1 1/4" trailer hitch cover with a Hyundai logo. ...Fits snug on Curt trailer hitches.
myminifactory
This is a hitch cover for 1-1/4" receivers.It has spring tabs on the side that fit snugly in my Draw-Tite receiver. I used PrusaSlicer's 2-color printing. Print the first few layers in one color, then change filament to a contrasting color for the...
thingiverse
This is a remix of a Mandalorian symbol receiver hitch cover, made in tinkercad. Edit: The first print came out fine, but was too short for the receiver on my Civic (Curt brand) so I've uploaded an extra long one that fits the Curt. ... After...
thingiverse
hitch adapter for 2" square hitch for using 1-1/4" racks don't cheap out on the shells and on the infill
thingiverse
Created a 1 1/4" receiver hitch plug. I borrowed the viking head from here: https://www.thingiverse.com/thing:2038500. ... Decided the small one was too small so made bigger.
thingiverse
A hitch cover with the Tesla logo for 1.5 inch hitches because why not
thingiverse
Hitch cover for 1.25 inch receiver. ...Holes might be a little tight.
thingiverse
This is my design for a tow ball / hitch ball cover for 1 7/8 sized balls - it has a torus inner restraint to stop it from popping off and a flat top for whatever you'd like to fuse to it.
thingiverse
... dangling ring to a solid knob. ...just pull out the ring, and tap the hole 6-32 thread. line the knob up over the hole so a 5/8" 6-32 socket head screw. the design in the picture converts a 1-3/4" pin into a 1-1/2" pin (from rim to the ball bearing).
thingiverse
Needed a hitch cover for my truck. ...Just added a flat plate to the hitch cover for the logo. Designed the logo from a pic using Fusion 360 and added it to the hitch using Tinkercad. ...
prusaprinters
I made this to try and keep my Ramps 1.4 cool, and keep the debris from the cnc out. Wire management should be easy and provide for better cooling of the drivers. Lcd header and wires still fit.</p> <p>The ramps set gets snapped into place, put the...
thingiverse
I made this to try and keep my Ramps 1.4 cool, and keep the debris from the cnc out. Wire management should be easy and provide for better cooling of the drivers. Lcd header and wires still fit. The ramps set gets snapped into place, put the board...
thingiverse
This is a Autobots trailer hitch cover with tabs sized for 1.25" hitches. Measure the end of your hitch to the center of the holes to determine which length you need. For instance, on my factory Honda Element, it's 4cm end to center. ...I included a...
thingiverse
Update 2021/02/18 - Added models with a slightly smaller logo (this is the one shown in pictures and on car) This is a Decepticons trailer hitch cover with tabs sized for 1.25" hitches. Measure the end of your hitch to the center of the holes to...
thingiverse
[Timelapse print and demo video](https://www.instagram.com/reel/Cgap3arA-cl/) The1.25" model has been modified to be one-piece with extra strength attachment at the end of the 1.25" hitch. The hitch has also been lengthened an extra 10mm to fit into...
thingiverse
This design adds locking tabs to prevent a rubber Curt 1.25" trailer hitch tube cover from working its way out over time. I'd suggest PETG rather than PLA for its higher temperature resistance, and printing with 100% infill makes drilling holes for...
cults3d
Automatic coupler for model streetcars and metric gauge trains. ... 1/22 scale coupling (IIm)
thingiverse
This cover is made to fit a 1 1/4" hole and will hold up to a 1/2" thick power cord. I used this in an rv bathroom to add some water resistance to a hole for the water heater power cord. ...
thingiverse
This is a cover for BTT SKR 1.3/1.4 boards, gives access to power connections and routs air from fan over stepsticks. I am using it with X,Y,Z, and E0 populated, it may need to be modified to fit E1. I use 20mm standoffs to mount my boards so i can...