1 1 4 inches to mm 3d models
2725690 3d models found related to 1 1 4 inches to mm.thingiverse
Collect three vacuum lines - from 40 mm, 2 inches, 2 and 1/2 inches to 4 inches Main part test and print in ASA - (0.6mm. 255C. 115C. 60% in fill, 15 % Fan, CURA DRAFT- 0.2mm lh) Feel free to support my projects!
thingiverse
The marking on this set is in inches (hence : 3/4, 5/16...) Sizes : 1/4" - 5/16" - 3/8" - 7/16" - 1/2" - 9/16" - 5/8" - 11/16" - 3/4" Estimated Print time @ 70mm/s : single bit : from 1 to 5 mn small set (1/4" to 1/2") : 15 mn big set (9/16" to 3/4")...
thingiverse
I needed a 1 1/4" to 50 mm hose adapter and ended up with this design. You can save some significant printing time if you set the infill pattern to "concentric". I also created a 50 mm Adapter with flange. Check my other tings if you have a need...
thingiverse
Hex bit to square adapter. ...I use it with my Bosch IXO.
thingiverse
Inner diameter is 2.5" two point five inches to 1.75" one point seven five inches. Height is 3" three inches. Wall thickness is 0.15" zero point one five inches. Takes about 5 hours to print. ... If it's a bit tight which mine was use some heat when...
cults3d
Separator from 1 to 4 mm. ...Ideal for separating tiles, drawers, lids, etc.
grabcad
Custom coupling from motor shaft with outer diameter 4 mm to shaft with inner diameter 1/4 inch. Material: brass.The motor axis is fixing with Clamp and M3 Set screw fastening and the shaft axis is fixing through clinch.Very compact design.
thingiverse
Bit adapter that has a standard 1/4" (6.31 mm) shaft that goes to a pentagonal (nominal 5 mm side length). 11 May 2017: I messed up the hex dimensions. They've been fixed with updated SLDPRT & STL files. ... 13 May 2017: It was too big on the hex...
thingiverse
Hexagon socket adaptor to 1/4" square. Different sizes from 7-20 mm. Not recommended for screws that need high torque. The hex-shape width is 0.15 mm bigger so that standard nuts and bolts can fit. I only tried PLA, maybe other materials are...
thingiverse
Instructions Print with high quality (I printed 0.1 mm per layer) to get fine female thread. This part designed to be used with 3 types of vacuum sources: Hair dryer (to use with hair dryer - go and print adapter...
cults3d
This is adapter for 3/4" standard water pipe to 30 mm diameter pipe, that I use in my projects.
thingiverse
... a Bosch IXO cordless screwdriver with a 10-mm-nut. ... The inner diameter fits on to the grinder axis, the outer into the nut. OpenSCAD-Code: difference(){cylinder(r=9.9/sqrt(3),h=18,$fn=6,center=true);cylinder(r=7.1/sqrt(3),h=18,$fn=6,center=true);}
thingiverse
... al my other adapters, so I designed this simple model to fit into my electronic screwdriver. ...The Fusion 360 file is added to the project, so you can adapt this model for your own needs. I also glued a smal (4 mm) neomydium magnet into the socket.
thingiverse
fast print - 1mm thick Card has 4 circles with various gaps between them from .4mm to .1mm as labeled on card. Useful for seeing where your printer will start "gluing" parts together. Gaps & Tolerances .1mm should be a tight fit for an FDM...
thingiverse
This is modeled to work with a ridgid shop vac 1 3/4 inch hose to a 1 inch hose to handle more vacuum attachments. ... 100% infil use heat to form fit after printing.
thingiverse
The 5 mm hole is suitable for NEMA 17 stepper motor shaft and the 1/4 inch is for the ACME threaded rod. Now Version 1.1 includes some minor tweaks such as: 1) A middle notch to improve the clamp flexibility. 2) M3 hex nut cutouts to make tightening...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: output_units = Metric inline_junction_type = round input_size = .5 strength = 1.0 input_units = US vault_connector_ratio = 1.8...
thingiverse
cube([25.4, 25.4, 25.4]); The cube should print with sides of 1 inch or 25.4 mm. I'm printing on a very basic printer - the Malyan M200 (same as Monoprice Select Mini) and mine comes out plus/minus 0.1 mm so I'm really pleased with that result. ...I...
thingiverse
This is a clamp for holding a meterstick or similar object parallel to a half-inch (12.5 mm) or smaller support rod. There are features for 10-24 hex nuts to provide the clamping force with a 10-24 machine screw or thumbscrew. ...I use Loctite 40140 to...
thingiverse
This is designed to spot clean carpets using a wet vacuum with a 1.25 (1 1/4) inch hose. The outer diameter of the attachment point on the hose is 1-1/4" so the inner diameter of this attachment is close to 1-1/4" as well. My wet vacuum didn't...
grabcad
Mobile clamp used in tubular scaffolding. ...Works on 1 1/4" tubes. ...Joints of any degree are possible.
grabcad
Fixed clamp used in tubular scaffolding. ...Works on 1 1/4" tubes. ...Only 90 degree joints are possible.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1246651 Instructions Using the following options: SmallEndDiameter = 46 TaperLength = 25 SmallEndLength = 25 InsideStop = no LargeEndDiameter = 65 SmallEndMeasured = inside LargeEndLength = 25...
thingiverse
i need this reduction to connect a small hose to a circulation pump. ...it becomes a water cooling system for my welding machine.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1246651 Instructions Using the following options: SmallEndDiameter = 46 LargeEndMeasured = inside SmallEndMeasured = inside SmallEndLength = 25 LargeEndLength = 25 LargeEndDiameter = 102...
thingiverse
I created this spacer to mount my usb charging port to my handlebars since all the good mounts that I've found so far are for 1" bars and my old Kawasaki KZ305 has 7/8" bars. The mount I was inspired to remix this from is probably one of the...