1 10 scale rc drift cars 3d models
1307016 3d models found related to 1 10 scale rc drift cars.thingiverse
As for wheels you can use any 1/10 scale drift rims and tires, but I have modeled these custom rims here https://www.thingiverse.com/thing:4279969. =========================== <h1>Parts</h1> I am still using a few parts that are not 3D...
thingiverse
Specs~ 12mm hex 13mm offset 27mm wide 52mm diameter This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/cIFnkYpHyO6
prusaprinters
A wheel stand to lift you RC car off the carpet or floor. Quick and easy to print. Flip the model upside down to print without supports. ...10% infill is more then strong enough also 2 perimeters.
thingiverse
1/10 Car battery. Modeled off of Optima YellowTop. Will look great for drift or crawler and in scale garage or workshop. Shouldn't need supports. ...Recommend slower print speed because of small details.
grabcad
Wheel for 1:10 scale RC drift car. This is a work in progress, but I've recently had it printed (ABS) and it works realy well. Seems strong enough for sure. It is part of a bigger project as some of the screenshots suggest. ...Stay tuned...
pinshape
1/10 scale rc drift car bumperless rear bash bar also could put your body on even the bar still attach so you could show it anytime tested on yokomo yd-2
thingiverse
Simple exhaust for RC vehicles 1:10 scaled. ... Perfect for RC drift Message me if you want other RC stuff
thingiverse
I am pretty sure the wheel will works on any other 1 10 scale cars with 12mm Wheel nuts. Enjoy! Instructions I print this wheel with as many shells as slicer will allow using ABS plastic. This...
thingiverse
Perfect printable drift wheel for 1:10 scale on-road rc cars. They are so smooth, they glide on carpet track no problem. They have barely any friction when sliding. First Test Run Here:http://youtu.be/AIE2ieG4lOs Check out the video on the car with...
thingiverse
This is a little collection of gadget for 1/10 scale rc cars
thingiverse
Tires for RC cars, compatible with 3D Sets [3D-printed RC cars](https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex...
prusaprinters
Tires for RC cars, compatible with 3D Sets 3D-printed RC cars (https://www.3dsets.com/). Print using TPU. Mirror the model to print full sets of four tires. Tires have 45mm inner diameter for a tight fit, and therefore can't be printed with semiflex...
thingiverse
RC drift tires 52x62x26mm. Follow me for more, write e a message if you want custom tires design (p.s. ...it's free!!) Print it in tpu
grabcad
Want to set up an RC drift course? ...Print some of these road cones and set up a track to slide! 1/10 scale road cones for your 1/10 scale RC!
thingiverse
1/10 scale supercharger, made to use m1 screws to attach the front to the body and the body to whatever you are putting it on, other parts can be glued. I would recommend printing each part individually rather than the whole. ... Will look great on a...
thingiverse
console central intérieur rc 1/10 pour cokpit
cults3d
Parcel shelf for RC drift car This fits perfectly in my Pandora Origin Labo S14 but can easily be trimmed to fit others Print flat with 15% infill I used PLA+ at 195/65 I use a Brim to make sure it prints flat. ... Check out my insta for more projects...
thingiverse
Parcel shelf for RC drift car This fits perfectly in my Pandora Origin Labo S14 but can easily be trimmed to fit others Print flat with 15% infill I used PLA+ at 195/65 I use a Brim to make sure it prints flat. ... Check out my insta for more projects...
thingiverse
This is a 1:10 scale drift wheel. Print the wheel and tire separately. The wheel and tire fit together with two notches. ...add a thin bead of Super Glue in between the wheel and tire to secure the them together.
thingiverse
... boot a bit. Flat underside so might need a light sand to fit. 125mm wide and 15mm deep (ignoring the curve. So scale it in your software before you print to fit your boot width. With or without bolts, your choice. Enjoy! ... Drift Spot.
thingiverse
It is a 1:10 scale RC car track signal light bridge. Lights are externally mounted after buying from any store. All towers are glued with any glue which is used to join plastic parts. You can also drill holes at the sides of tower to mount screws.
thingiverse
This wheel has been designed to compliment a 1/10 scale widebody RWB Porsche RC (files currently in production) with 12mm hex fixings . The photo is a print in PLA at 0.2mm with a 20% infill and supports on where touching the bed. To give the...