1 2 end cap 3d models

Customized version of https://www.thingiverse.com/thing:5217813 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5217813

Customized version of https://www.thingiverse.com/thing:1341945 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341945

Customized version of https://www.thingiverse.com/thing:5217813 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5217813

Customized version of https://www.thingiverse.com/thing:1943463 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1943463

Customized version of https://www.thingiverse.com/thing:1341945Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341945

Tube or pipe closure device.

Female Rod End for Checking Swivel Clearance or Fitment.

Tube end cap for a 25 mm or 1 inch square tube.http://rjk.co.za/index.php/diy

Tube end cap for a 25 mm or 1 inch square tube.http://rjk.co.za/index.php/diy

end cap to fit 3" OD tube

End cap for wall electric wire box.

End cap for 30x30 alu extrusion.

End cap with a half inch thread.

Unirac SolarMount End Clamps Cap for rail

End cap for Aluminium profile 4040.

Cable raceway end cap 40mm x 60mm.

Bicycle bar end cap / plug roadbike

This is a protective cap designed to conceal exposed metal rail ends on a fence. ...The rails measure approximately 2 inches wide by 1 inch deep, specifically 2.0 inches by 0.95 inches in dimension, with a thickness of 0.0325 inches.

Simple cap for 1/2" EMT metal conduit pipe to protect the ends that are sometimes sharp.

I designed a 3D printed bar end cap to replace a lost cap on my road bike. This is ~1.0" OD and ~.73 ID. ...Using a 10-24 x .625 BHCS (McMaster 97763A337).

I designed a 3D printed bar end cap to replace a lost cap on my road bike. This is ~1.0" OD and ~.73 ID. ...Using a 10-24 x .625 BHCS (McMaster 97763A337).

End cap for Cardboard tubes from Exotic Firearms, maybe other tubes for 37mm. Printed .2 with 25% infill with brim and standard supports touching build plate. ...

... however, its durability remains untested. Additionally, 1.25 and 2-inch sizes are available with a 1.5mm air release hole included. Once completed, a review and picture will be posted. ...Note that the makerbot's electronics are almost finished.

Customized version of https://www.thingiverse.com/thing:1341945Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341945

Customized version of https://www.thingiverse.com/thing:1341945 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341945

Customized version of https://www.thingiverse.com/thing:1341945 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1341945

Customized version of https://www.thingiverse.com/thing:5217813 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5217813