1 2 ferro rod holder 3d models
1676001 3d models found related to 1 2 ferro rod holder.thingiverse
... rods for fire starting it should fit any of the half inch rods. ... for: https://www.amazon.com/bayite-Survival-Starter-Ferrocerium-Paracord/dp/B00S6F4MO6/ref=sr_1_5?keywords=ferro+rods&qid=1638770570&sr=8-5 but can be used and half inch ferro rods.
thingiverse
... the diameters to fit a 15/64" rod and also shifted the bracket to one side for easy flat printing with no supports. ... Almost perfect size for 15/64" rod, just run a drill bit down to clean up any anomalies and it fits so snug it won't fall out.
thingiverse
I wanted to make a ferro holder for my BK2, didn't really know where to start. It just happened that I had access to a MakerBot one semester. ... I used two nuts and bolts to connect this to my knife.
thingiverse
... use a hairdryer to soften it. ...Print everything with outside walls in fuzzy skin. I did 0.2 and 0.2. the original file was from https://www.thingiverse.com/thing:3991726/comments but i made many changes. This is for a half inch ferro rod btw
thingiverse
The ferro rod hole is on a slight angle to keep the rod and sheath aligned. I tape it to my sheath with electrical tape since it allows for a really tight fit because it's so stretchy and it has lots of colors to boot. I'll be bringing this on...
thingiverse
Hello, i made this easy ferro rod 4.5mm x 45mm ferro rod holder for my srm knife. Need some sanding and super-glue to attache ferro. ...Hope you like it :)
thingiverse
This is my modifyed version to hold a Ferro Rod in the companion mora knife. you can put a tic tac case behind to hold any kind of stuff. ... i`m using bicicle inner tube to hold in place (the tic tac case) or, insted you can put 4~5 meters...
thingiverse
This is a Ferro rod, Lighter, and cordage manager I made for my Mora Heavy Duty
thingiverse
Once the ferro rod is inserted into the handle, approximately 4.8 inches stick out from the handle. Lots of surface area to make some great sparks! Make sure to rotate the STL model file 180 degrees in your slicing program so that the handle...
thingiverse
A very simple, small print that adds a simple ferro rod and striker to your key ring in a very unobtrusive fashion. ... Video: https://youtu.be/j7vVIbN8L3Y
prusaprinters
I wanted it to be as convenient and secure as my knife sheath, but since I wear the knife more often than I'm in the woods, I don't always need the ferro rod, so I figured rather than add it to the sheath as some models I found, I'd just make it a...
cults3d
A ferro rod mount I made for my CRKT Folts Minimalist, holes don't really line up but zip ties make up for everything. ...Currently made for a horizontal holster (as seen in the picture) but can be used vertically at an offset.
prusaprinters
A very simple, small print that adds a simple ferro rod and striker to your key ring in a very unobtrusive fashion. Video: https://youtu.be/j7vVIbN8L3Y Category: Sport & Outdoors
thingiverse
This is a Ferro Rod hold I made for my Mora Robust. ... Enjoy
thingiverse
I wanted it to be as convenient and secure as my knife sheath, but since I wear the knife more often than I'm in the woods, I don't always need the ferro rod, so I figured rather than add it to the sheath as some models I found, I'd just make it a...
thingiverse
This is a handle for a 5/16" ferrocerium rod with a 4mm lanyard hole (large enough for 550 paracord). ...Use a little 5 minute epoxy to secure the rod in the handle, or the adhesive of your choice.
grabcad
(Dimensions for the rod holder can be viewed in image labeled Dimension Image) This design lives up to the Trapper Life Style: 1) It is made from ENVIRONMENTALLY FRIENDLY material 2) It is made with DURABILITY and STABILITY in mind 3) It's low...
thingiverse
Needed a curtain rod for a curtain in the basement. ...I had 1/2" PVC on hand, and needed it to fit in a very specific location. ...Drew this up in OnShape and it works great.
thingiverse
Designed to mount a 1/2" diameter curtain rod to a wall using four screws or nails. The topology has been optimized to remove unnecessary material and to make the design look extra awesome. ...:) The holes are on the small side, so I recommend either...
prusaprinters
They feature a cut out for 2 cabinet screws for mounting. Installation:I put in one screw in the bracket where I want the rod located. Next slide the bracket on the the EMT pipe then the EMT pipe into the bracket on the wall. Put a level on the...
thingiverse
When we renovated a very small closet, to a walk-in closet, we added 1-1/2" conduit metal pipe in place of the old wooden closet rods. It gave the modern look that the rest of the new closet had, so it was perfect. You have to cut the rod to...
prusaprinters
When we renovated a very small closet, to a walk-in closet, we added 1-1/2" conduit metal pipe in place of the old wooden closet rods. ...It gave the modern look that the rest of the new closet had, so it was perfect. You have to cut the rod to length,...
prusaprinters
When we renovated a very small closet, to a walk-in closet, we added 1-1/2" conduit metal pipe in place of the old wooden closet rods. ...It gave the modern look that the rest of the new closet had, so it was perfect. You have to cut the rod to length,...
thingiverse
This object was made in Tinkercad. ... https://www.youtube.com/watch?v=ivFaBWAaCGs&t=1s For 8mm DIA ferro rods . Hole spacing 38mm for mount.. ... Printed in PETG for strength .
thingiverse
... of http://www.thingiverse.com/thing:324416 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=324416 Instructions Using the following options: text_size = 2 text_itself = FERARRO text_font = Letters.dxf show_text = yes
thingiverse
A sphere shaped curtain rod holder for 1/2 Inch wood dowels. About 1-7/16 inch (36mm) in outer diameter. Mount with #6 pan head screws or strong double sided tape. ...
thingiverse
This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/j7phciKKzvl Instructions 5/16" rod holder, slides over 1/2" pvc pipe. ... Printed at 30% infill, no supports.