1 2 tube clamp 3d models
1452144 3d models found related to 1 2 tube clamp.thingiverse
Made to clamp 2 pieces of 1-1/2 square steel tube together and has holes to mount a metal bracket to hang my milwaukee drill from.
thingiverse
This is a lot of 1/2" Pipe Clamps for modeling or small woodworking projects. They use 6mm or 1/4-20 bolts to tighten to the pipe. There are many shapes and sizes for many applications. My other clamps were too big or too small, so I made some to...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=909819 Instructions Using the following options: clamp_bolt_diameter = 4.5 clamp_contact_thickness = 10 mount_rotate = 90 clamp_bottom_hole_style = 1 gopro_buckle_notch_width = 3.75...
prusaprinters
use for 1.25" tubes, hardware is 1/4". one side has counterbore for socket head cap screw if you want to mount something on a stud. the other side has a hex bore for a captive nut. this lets you choose which side of the screw you want to use to mount...
thingiverse
A 2-Piece print. I've printed and used a number of these with PLA. ... A new version is coming soon with a hinge on one end.
thingiverse
This is a simple clamp I designed for running 3/16 diameter brake lines along a 1 1/4 Inch tube frame in a DF Goblin kit car.
thingiverse
This is a tube clamp for a 1.75 tube. It is very similar to a tube clamp for a rouge Fab M600. The print allows you to insert a nut and run a bolt through it to lock it down. I have a regular version and one that has been elongated to glue a...
thingiverse
These can also be used for 1/2" pipe clamps for plumbing purposes as well. Tolerances aren't super tight (~1mm). The clamp can easily be slid up and down when mounting but they are tight once screwed in. There are two versions. One is a 5mm...
thingiverse
This clamp fits a standard 1/2" pvc pipe and will secure using an M4 16mm long and a nut. Probably a #6 would fit as well, but I haven't tried. As you can see, I'm using them to secure a couple of candelabra bulbs that I had left over from removing...
pinshape
Summary This clamp fits a standard 1/2" pvc pipe and will secure using an M4 16mm long and a nut. Probably a #6 would fit as well, but I haven't tried. As you can see, I'm using them to secure a couple of candelabra bulbs that I had left over from...
grabcad
... to the steering mount unfotunately the weight has gone up a tad at 747 Grams. May shave a little weight off this on still or re-think & go trellis idea ( shame its not a titanium trellis tube Fab would look cool with the fram being trellis too).
thingiverse
G27 Shifter clamp adaptation for a 1 inch square steel tube
thingiverse
... Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=2045892 Instructions Using the following options: number_of_fasteners = 1 screw_hole_size = 4 screw_hat_witdh = 7 screw_hat_thicknes = 2 min_part_thickness = 3 cable_diameter = 13
grabcad
... steering support unfotunately the weigh has gone up again 760 grams. ...Will maybe shave some more weight off or may just go down the trellis look instead ( shame its not a titanuim trellis clamp like the frame would make a nice fab plus no vibration).
thingiverse
... tube. ...Uses standard 1/4-20 nuts. It will obviously melt on a muffler but may have other uses as a tube clamp or mounting surface on 1" OD pipe or tube. I was very suprised at how strong this clamp is printed fully filled. ...3D print with support.
cults3d
This design can be used to join a flow sensor and a solenoid valve of 1/2" diameter
thingiverse
This little thing can be built in for clamping the PTFE-tube that leads to the extruder of a Voron 0.1. When you load or unload and need top push or pull hard, the tube may come out of its position. I did not want this, so I designed this. ... Works...
thingiverse
This is an adapted Version of the original Ultimaker bowden clamp fix but I've made it for the Ultimaker 2. My bowden tube has come out a few times on prints so this was evolved as a preventative of it happening again ( and is much better than...