1 25 to 1 5 hose adapter 3d models

This adapter enables connecting a substantial Intex 1.5" hose to a compact Intex 1.25" hose. The larger end demands an Intex gasket and the smaller end requires an O-ring. The smaller end has somewhat limited geometry, but applying some teflon tape...

This is an above ground pool hose adapter that allows you to connect a 1.5 to 1.25 inch inside diameter size hose. Simply attach the clamps and use Teflon tape or pressure tape to ensure a secure seal. ... Print Settings: Printer: i3 Rafts: Not Required...

... 1.5 inch ports. I'm adapting this to a 1.25 inch vacuum hose, CRAFTSMAN CMXZVBE38662 to be specific. ... Hopefully this helps anyone that ran into this problem as there seems to be no standard with vacuum hose sizes and readily available adapters.

This quick little adapter was designed to adapt a 1¼" pool hose to fit a 1½" connector on a pool filter's Waste port. Although it's not built for high pressure, you can use it on the intake side of a pool pump, but I wouldn't recommend using it on...

This quick adapter was designed to convert a 1¼" pool hose into a fit for a 1½" connector on a pool filter's waste port. It isn't built for high pressure, so while you can use it on the intake side of a pool pump, I would not recommend using it on...

I drew up a makeshift adapter to fit a 1¼" pool hose onto a 1½" connector on a pool filter's waste port. This quick fix isn't designed for high pressure, so while you can use it on the intake side of a pool pump, I wouldn't recommend using it on the...

Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1246651

No barbs on the hose half didn't cause any issues.Modeled with a flat bottom so you don't need to deal with supports or bad overhangs. If you print it with the flat side down, as intended, the threads still come out nice and there's no need for...

To modify the 2.5-inch dust port on my Hitachi table saw, I had to accommodate the 1.25-inch hose from my mini ShopVac since the correct adapter wasn't available. ...Here's the solution.\r\n\r\nThis adapter fits snugly within the 2.5-inch port -...

LargeEndMeasured: Inside LargeEndDiameter: 42mm LargeEndLength: 33mm SmallEndMeasured: Outside SmallEndDiameter: 35mm SmallEndLength: 40mm TaperLength: 20mm WallThickness: 1.4mm

So to permit 1.5" hose to old 1.25" tool kit I created these adapters. Includes one straight adapter, one 30 degree angled adapter, and one 1-1/4 inch mini knife attachment for use in cleaning up shop bench top. Fusion 360, STL, and gcode files...

The design accommodates an optional connection of a 1.25 inch pool hose to a standard garden hose. ...The user prints the O-ring component with TPU material properties.

Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. Did this so I can use the pool pump to empty out the pool. ...Also see my 1.25 hose adapter to taper on the inlet of the pool hose.

Many workshop tools have a 2.25 inch vacuum hose adapter and most vacuum have 1.25 inch hoses. This has a large 2.25 outside diameter that will fit into a 2.25 inch hole as on the Wen Sander. The inside small hole is for a 1.25 inch hose on the shop...

The adapter fits tightly onto the 1 1/4 inch hose of the ShopVac. It can be easily removed after use. ...This makes it ideal for attaching to a Wen 6515ST belt sander.

I wasn't able to find a suitable replacement adapter for the Ridgid floor attachment specifically so I was able create one based on the original. ...No scaling required, supports are required.

This adapter takes a Ryobi P7131 vac and adapts it to a 1.25" hose. ... I'm using the hose found in the Ryobi kit A32KN05N

needed to make a quick hose adapter for the shop vac. ...this allows you to use the long small 1.25" end of a shop vac hose in the wide 2" end of the vac or other hose.

This should fit a hose with a 1.25" OD and a 1.0625" (1 1/16") ID This allows you to use a hose like the one that comes with the Home Depot Bucket head for approximately $24+ the cost of a 5-gallon bucket. A longer hose is recommended vs the stock...

Adapts my Bosch palm sanders dust port to a 1.25 vacuum hose. This is a common hose size found in many central home vacuums as well as automotive vacuums/car washes. ... They are far more flexible than the 2in shop vacuum hose making them ideal for a...

4" Dust collection port to 1.25" vacuum hose. .STEP included. AP214 Can be easily modded to fit different size dust collector ducts and hoses. 0.25 Wall for strength. Can be printed in anything. Large OD on build plate, no supports needed. ... ...

This is my third attempt at it, and I added longer neck sections so the adapter securely fits onto the sander and 1.25" hose. It works fantastically well, allowing me to lift and drag the sander around by the hose! I printed this adapter in TPU for...

This is the third iteration; I added longer neck sections so it securely fits onto the sander and the 1.25-inch hose. It functions perfectly, allowing me to lift and drag the sander around by the hose! I printed it in TPU for a bit of flexibility...

I attached a straightforward little adapter to connect a 1.25-inch hose directly to the pump supply line of my pool, giving me the ability to use this hose to suck up sand and small debris from the bottom with ease. ...This setup works perfectly with my...

The following instructions will guide you through a precise process to integrate this accessory into your planer: First, carefully insert the provided component into each port on your machine until snugly seated. Next, apply a couple of small...

hose connector 1.25 inch to 1.0 inch 25,5mm to 32mm

I'm using a vacuum adapter to transition from a 1.25-inch vacuum hose to a 2.5-inch dust port on shop equipment. The process requires some light sanding of the interior to achieve a snug fit onto the vacuum/dust port. ... Print Settings Printer Brand: ...

Adapter from the Black & Decker belt sender, model DS321, to the 1 ½” hose. ...

Ryobi or Wen Power Tool Adapter for Shop Vacuum Converts 2.5 to 1.25 - Tested Successfully with Ryobi Band Saw and Wen Bench Top Sander Using High-Quality PLA Printed Version Works Flawlessly.

... my Ridgid 4 gallon 5HP shop vacuum uses a 1.875 (1 7/8) inch hose. Vacuum model is WD4070 to be specific. Hopefully this helps anyone that ran into this problem as there seems to be no standard with vacuum hose sizes and readily available adapters.