1 4 20 nut 3d models
1285489 3d models found related to 1 4 20 nut.cults3d
Knob for use with 1/4-20 nuts, it can probably be scaled for use with nuts of other sizes. ... Filaments: (full list can be found on thrinter.com) -- 3D Solutech See Through Blue ABS
thingiverse
Knob for use with 1/4-20 nuts, it can probably be scaled for use with nuts of other sizes. ...Filaments: (full list can be found on thrinter.com) -- 3D Solutech See Through Blue ABS
myminifactory
Knob for use with 1/4-20 nuts, it can probably be scaled for use with nuts of other sizes. ... Filaments: (full list can be found on thrinter.com) -- 3D Solutech See Through Blue ABS
thingiverse
Didn't see any others on here so figured I'd make one. ...Its just a stop for a 1/4-20 nut press fit in. so far works really well. ...I used 4 walls and 99 bottom layers to make is solid.
thingiverse
Too lazy to buy a nut? I got you covered. This is perfect for any tripod mount, which is what I made it for, but you can do whatever you want with it. Except eat it. Or feed it to others. Or feed it to animals. ... I guess just use your best...
thingiverse
I'm working on a some small project now and needed few knobs of different sizes for 1/4 20 nut (it is about 11mm from side to side / 5.6mm deep). Here are few variants that I made. If fit is too tight I usually preheat nut on a lighter and just push...
thingiverse
... matches some commercial knobs I have on hand. ...Accepts a 1/4-20 nut (11mm OD) that will press fit in (no heat needed). ... I printed with the gyroid infill pattern for increased strength in the X and Y directions, but it's not really necessary.
prusaprinters
Accepts a 1/4-20 nut (11mm OD) that will press fit in (no heat needed). Print instructionsDesigned so that no supports or rafts are necessary. There's no bridging or overhangs to complicate matters. ...I used 20% infill and it's sufficiently strong; if...
thingiverse
This is a collar for the standard tripod mount nut (1/4-20). The nut is inserted in the middle and can be tightened and loosened with fingers. I printed this for a DIY tripod clamp. ...The print is really tight for a standard nut, some sanding or filing...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: screw_hole_diameter = 55 knurled_strong = 6 knurled_density = 50 knurled_height = 50 bottom_thickness = 0.6 screw_hole_length = 100...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: diameter_2 = 125 diameter_1 = 150 nut_width = 11 screw_hole_diameter = 55 nut_thickness = 4 cross_section = 0 knurled_height = 100...
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
6 star knob for 1/4" 20tpi nuts. ... Print is a very tight fit, will need a hammer to press the nuts in.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1562501 Instructions Using the following options: boltDiameter = 7 boltHeadThickness = 5.5 pointRadius = 10 baseHeight = 15 rBottomFillet = 2 boltHeadHeight = 5 rTopFillet = 10...
thingiverse
... attached to the channel. In my case it would be taking half of the printer apart in order to slide the nut in. ... Enjoy and let me know if you want to change anything about it, it was just a quick 10 min model so please don't judge :) Post-Printing
thingiverse
This knob works with a 1/4-20 Nut and Washer. ...Does not require any support.
thingiverse
these are tight thumb press fit for 1/4-20 nuts you could also use them instead of wing nuts i plan to use them for power supply connections cause i am a cheap skate
thingiverse
This is a foot I made for a staning shelf 1" round with inset for a 1/4-20 nut
thingiverse
Press Fit "Thumb Screw" shell for 1/4-20 Nut. ... It can be used for any application but this was designed for my 1-inch, 1.5-inch and 2-inch Enhanced Sanding Blocks.
thingiverse
A remix of longhairedhippy's design. ... 1. Enlarged screw whole to accept 1/4-20 screw. 2. Changed screw cutout to accept a 1/4-20 nut. I connected this part to a 1/4 Gopro Adapter linked (affiliated) below. ... https://amzn.to/45D1Ufc
thingiverse
This modifies the original to use a 1/4"-20 nut to screw onto a normal tripod or quick release plate. kinect_nut.stl is the modified version. ...kinect3C.stl is the original, for use with the attached .scad if you want to modify the thickness or nut...
thingiverse
This is simply a 1/4-20 nut which are commonly used for tripod threads. Customized version of http://www.thingiverse.com/thing:193647 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=193647 ...
cults3d
Slightly modified to accept a standard 1/4"-20 nut (superglue in) and to be printed without any support (max overhang = 60 degrees) I don't actually have a GoPro myself to confirm fit; I just modified 3D_CC_design's model for a friend. ...Also it was my...
thingiverse
Slightly modified to accept a standard 1/4"-20 nut (superglue in) and to be printed without any support (max overhang = 60 degrees) I don't actually have a GoPro myself to confirm fit; I just modified 3D_CC_design's model for a friend. ...Also it was my...
thingiverse
3 point knob for 1/4-20 metal nut. This one is a hammer fit. You will need to use a hammer to press the metal nut into the opening. ... Of course, you can always scale it up if the fit is too tight.
thingiverse
Gun rest/yoke to be mounted on a tripod with 1/4-20 nut. The curvature fits my S&W X-Frame and Governor very well. Two ways to print this: 1) As is, pausing the printer to insert the nut just before the cavity is capped off. 2) On it's side,...