1 4 20 wingnut 3d models
1213014 3d models found related to 1 4 20 wingnut.thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=713300 Instructions Using the following options: nut_width = 11 bottom_thickness = 0.6 screw_hole_diameter = 55 knurled_strong = 5 supportless_friendly = 1 knurled_height = 50 cross_section = 0...
thingiverse
A skateboard shaped wingnut for a shelf that I made, has an inset for a 1/4-20 nut.
thingiverse
Here is a 1/4" wingnut driver that uses 3/8" socket drive. It holds the wingnuts nicely so you can manipulate the drill without the nut falling out. I had a job that required me to assemble a few hundred 5/16" wingnuts and made a driver for them.
thingiverse
A 1/4-20 wingnut or brass knurled nut makes it easy to tighten by hand. There are 2 variants, and in my application (attached to a 2-segment wooden extension arm) the base of the mount is at the bottom. However, the holders could be mounted...
thingiverse
This one is for 1/4" bolts, with a 7/16" head. It should play okay with a 6mm bolt too. It was made as part of a couple other projects I'm working on, but it's such a nice wing nut, I figured it could use it's own thing. ... The photo shows a...
thingiverse
Wingtip camera mount for RV12 Need 1/4"-20 studs, wingnuts, and very short 1/4"-20 bolts to finish. ... https://youtu.be/BH0ppCLILfY
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
... from the bolt using diagonal cutters/pliers/dremel cutter/hobby knife. Mount your camera and your done. The clamp is designed to not really need hand tools. In fact you only need the same tension if you used a 1/4-20 wingnut and your hand.
cults3d
1 1/2" diameter small knob for 1/4" nuts of bolts, this one is very useful for small jig or anywhere you need to turn a nut or bolt and don't want to use those wingnuts that most of the time are not comfortable to turn.
thingiverse
Thumbwheel for 1/4-20 bolt. ... Fit is very tight, pull it through by tightening a nut on other side.
thingiverse
Designed a new knob for a tripod that used 1/4-20 machine screws. ...Same profile as a Stanley screwdriver.
thingiverse
This is a simple knob that fits a 1/4-20 hex head bolt. ...I used four of these knobs for my 3-D Push Block for my table saw, but there are many more applications for these knobs.
thingiverse
This is a 1/4 20 wing bolt and it has .55 inches of threads. I designed it on Fusion 360 and printed it upright out of petg standing on its head. It might be stronger if u printed it on its side but I you would have to do it with supports and make...
prusaprinters
Captured nut & Open nut Knob for ¼-20 nut. ... Captured nut will stop with color change to insert nut during print. </p>
thingiverse
... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=306072 Instructions Using the following options: knobHeight = 4.0 knobDiameter = 17.0 nutWidestDiameter = 12.46 nutHeight = 5.54 ridgeRadius = 2
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_height = 5 nut_thread_outer_diameter = 9 type = bolt nut_height = 6 head_type = hex nut_thread_step = 2 outer_diameter = 14 thickness = 2...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: thickness = 2 slot_width = 1 resolution = 0.5 step_shape_degrees = 45 thread_step = 2 inner_diameter = 8 thread_outer_diameter = 8 drive_type =...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: type = nut non_thread_length = 0 head_diameter = 12 socket_depth = 3.5 nut_diameter = 12 texture = exclude resolution = 0.5 inner_diameter = 8...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: non_thread_diameter = 0 head_height = 4 outer_diameter = 14 nut_step_shape_degrees = 45 texture = exclude socket_depth = 3.5 type = nut...
grabcad
Carbon steel threading die for 1/4-20 RH external threads. .363" thick with 1" hex. ...Tapered chamfer on start side with three relief cuts.
thingiverse
3D Printed Airtag holder attached with 1/4 20 screws. ...1 Attaches onto the camera cage, the other 2 secure the two halfs of the 3d print together.