1 4 3 8 1 2 socket set 3d models

... to hang and have the pipe wrenches organized. Measurement: 1/4 Inch. Recommendation: Depending on the brand of the key, it is recommended to give - 0.1 horizontal expansion in Cura, so that it fits perfectly. ... I am subject to recommendations -

1/4 stereo jack with switchessimilar to PJ-629HAN and many others chinese clones of [insert your brand's name]Datasheet: https://www.taydaelectronics.com/datasheets/files/A-1121.pdfPlease keep in mind production tolerances.

I needed a socket handle which I could hold and use like a key. This is my interpretation of that. ...I printed it at 0.3 layer height in ABS.

Storage for 3/8" sockets

Using Customizer, I Created This: http://www.thingiverse.com/apps/customizer/run?thing_id=1215001 Created Using the Thing Customizer Tool Thing Created Here:http://www.thingiverse.com/thing:1215001 Customize Me Choose Your Socket Numbers: Socket 08 =...

... for any damages. We developed this holder for the 11pcs TX socket set. You find the product in our shop: https://wiesemann1893.com/products/tx-bit-set However, the holder should be compatible with every other tx socket set of course =)

The prime link 8_4_1 model, displayed in a thin and thick version, is tied within a constant-radius tube when pulled taut. This design allows for easier printing with minimal support material. For additional details on this specific knot, refer to...

A customized version of the model found at http://www.thingiverse.com/thing:91496 has been created using the Customizer app with drive set to 6.35, tolerance at 0.2, size as 3, and depth as 10. ...Check it out!

Drive with a ¼" socket driver or a ¼" hex bit.

Bolt & Nut ( Inch )1/4" x Length 3/4"

Customized version of https://www.thingiverse.com/thing:892317 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=892317

Print Settings: Printer: Prusa i3 original MK2 Rafts: None Supports: None Resolution: 0.2 mm Infill: 50% is sufficient, but more can be added if necessary. Notes: Printed preferably from ABS to prevent warping of the material, which could lead to...

This fusion yielded two distinct versions, differing solely in the length of their 1/8" NPT ends. The V2 model boasts an approximately 3mm shorter extension compared to its counterpart. ... I employed version 2, pictured below, with a 100% fill density...

Bolt & Nut (inch)1/4" x 1 1/2"

https://www.thingiverse.com/apps/customizer/run?thing_id=615256 Instructions Using the following settings: Roadway Height Y Position: 0 Roadway X Position: 0 Block Height Ratio: 100% Reinforcement Used: No Stud Type: Solid Block Width: 3 units Wing...

A ¼" socket tray for organizing all of those annoying little bits on your Honeycomb Storage Wall

Tool holder for 11pcs socket sets. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 118,5mm W - 57,95mm H - 137,04mm We...

Tool holder for 11pcs socket sets. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned walls Pins: for peg boards of standard size Sizes: L - 118,5mm W - 57,95mm H - 137,04mm We design all...

Designed all my models in Fusion 360. ...used parametric design so I can make them work with any socket or wrench

The 3_1 trefoil and 4_1 figure-8 knots constructed so that their vertices lie on the cubic lattice. (The cubic lattice is the set of all points in 3-dimensional space where each of the three coordinates is an integer.) These knots were created by...

Tool holder for 8pcs socket sets. We provide two versions to download: Screw: 4mm holes for standard screws for mounting on wooden or stoned wallsPins: for peg boards of standard sizeSizes:L - 95mmW - 50mmH - 133mm We design all holders with much...

I wanted to try a different bevel gear set to get better torque than the original 2:1 gear set, but easier to maintain than using the in-line 4:1 planetary gearbox for an overall ratio of 8:1. This is a 4:1 bevel gearset with a helical tooth profile...

I wanted to try a different bevel gear set to get better torque than the original 2:1 gear set, but easier to maintain than using the in-line 4:1 planetary gearbox for a 8:1 overall. This is a 4:1 bevel gearset using a helical tooth profile with a...

Some testing shows that if you are more "delicate" with your sockets, and lift at a 90 degree angel you can print the model with the base down, for cleaner edges. ... I personally like that the marks from the supports add a bit of holding power to the...

10MM SOCKET HOLDER KEYCHAIN Printing Temperature: 190˚C - 230˚C Bed Temperature: 25˚C - 60˚C Printing Speed: 40mm/s - 60mm/s Fan: ON Direct Drive: Retraction Distance: 1mm Retraction Speed: 20mm/s

I wanted a tool to hold my 6mm socket while removing and installing nozzles. It works better for me than the open-end wrench that comes with the printer. ...Created in TinkerCAD.

... that it would fit both SAE and Metric sockets or wrenches. It has the collar around it to more easily remove it from a socket and so that it won't pass all the way through a wrench. ... I think it could be useful but obviously its made of plastic.

Customized version of http://www.thingiverse.com/thing:1215154 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1215154 Instructions Using the following settings: NUMBER OF SOCKETS: 4

Big thanks to Antbarbato for posting the Fusion files, that made it super quick and easy. Print Settings Printer Brand: Creality Printer: CR10S PRO Rafts: No Supports: No Resolution: 0.2 Infill: 25% Filament: Coex PETG random Category: Tool...