1 4 bolts 3d models
1172946 3d models found related to 1 4 bolts.thingiverse
This is just a quick knob for a 1/4" bolt to tighten a hold down clamp for my cnc. I ream it out with 1/4" drill then put a 4" bolt through it, tighten it up with a washer and nut and then use hot melt glue to seal up the top. I'll post pics later....
thingiverse
... made from is strong enough to withstand the force. Use with 2 or 4 1/4" bolts to secure the outsides, and single 1/4" bolt to provide a clamping force in the center + section. ...Secure the foot on the end of the bolt to provide even clamping force.
thingiverse
This is a knob that a 1/4" bolt can be pressed through and used for a tension knob. ... I
thingiverse
1/4 Bolt - Fits all webcams and tripod accessories. Print 100% infill Printed many times, threads work perfect! Thank you for your support. ... Donations @ https://www.paypal.me/realsamuel93
thingiverse
Uses any 1/4" threaded bolt. Seats inside the handle. ... Print Settings Printer: Sintron Rafts: No ...
thingiverse
Here are the handle if you can only find imperial 1/4" carriage bolts for this design. ... https://www.thingiverse.com/thing:3904218
thingiverse
This is a tripod part that uses four 1/4-20 bolts to screw into. The smaller bolt is the same threading as what is on the bottom of most cameras. ...Screws can be adjusted.
thingiverse
An L-Bracket for use with 1/4 inch bolts and washers. This is for use with extruded aluminum to make strong 90 degree joints. Customized version of http://www.thingiverse.com/thing:2226 Created with Customizer!
thingiverse
changed the hole layout to work with 1/4" bolts (i would assume 6mm bolts would work as well) on 1" on center peg board (the peg board on the Milwaukee tool boxes) as with all the battery mounts i find they fit alot better if scaled up a tiny bit, i...
thingiverse
I use it with Bolt Depot hardware (https://www.boltdepot.com/Hex_bolts_Zinc_plated_steel_1_4-20.aspx) but most ¼" bolts should work. I added spacers in case the knob needs to be raised to clear obstacles! For an example see...
thingiverse
This is a Knob I made for the 1/4x20 bolts I used for hold downs on my MPCNC. ... I used 1/4 x 20 inserts in the bed of my MPCNC and these knobs are made to be a snug fit so they hold the bolt not just slide over the top.
prusaprinters
I use it with Bolt Depot hardware (https://www.boltdepot.com/Hex_bolts_Zinc_plated_steel_1_4-20.aspx) but most ¼" bolts should work. The .3mf file is included if you want to slice for another printer. Enjoy!1/1/2022: I added spacers...
thingiverse
Bolt knob for 1/4" bolt. ...Pass bolt through now you have a hand adjustable bolt.
thingiverse
v1 pictured v2 spaces out the screws 6mm further - sized for #10 sheet metal screws and 1/4" hex bolt
thingiverse
This is a simple knob designed to press on the head of a 1/4" bolt. ...I am including the solidworks file and this could easily be converted for other size bolts.
thingiverse
These are designed for a 1/4" bolt, but could easily be scaled up or down. ... This is a newer version of my old thumbscrew (https://www.thingiverse.com/thing:2747398).
thingiverse
1/4 Bolt - Fits all webcams and tripod accessories. Print 100% infill Printed many times, threads work perfect! Thank you for your support. ... Shorter Version: https://www.thingiverse.com/thing:4784049 Donations @...
thingiverse
This is also bundled with my adjustable rifle rest but could be used for other things as well so I thought it should be offered by itself as well. ... It is use to make a knurled knob with a 1/4" bolt/stud epoxied in.
prusaprinters
This is a Gridfinity System M6 or 1/4" bolt holder based off of Zach Freedman's GridFinity System.I printed using 0.25mm layer height with PLA on my Lulzbot Mini v1.
thingiverse
Adapters for cheap selfie sticks to allow the mount of 1/4" UNC bolts or nuts. There are two models. First one with a wheel, so that you can screw the bolt/nut into your device. In the second model, the blot/nut is fixed. ... Quick video to help on...
thingiverse
... were just too large for this small cnc. I'm using 1/4in x 2in bolts and 1/4in nuts here. The clamps can be used flipped on either end with one end being shorter than the other per your needs. And there's 2 different sized clamps too. ...
prusaprinters
... small cnc. I'm using 1/4in x 2in bolts and 1/4in nuts here. The clamps can be used flipped on either end with one end being shorter than the other per your needs. ...And there's 2 different sized clamps too.</p> Category: 3D Printer Accessories
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=125529 Instructions Using the following options: CompressionNutDiameter = 10 CompressionBoltHeadDiameter = 10 CompressionBoltDiameter = 6.4 BearingDia = 22 RodDiameter = 9.6 showRod = 1...
thingiverse
Countersunk spacer, 10mm in height with an ID appropriate for M6 and 1/4" bolts. The version I actually printed was a little tight, I edited the ID to have a little more clearance but I have not printed it myself to verify. Either way, I've...
thingiverse
Customized version of https://www.thingiverse.com/thing:713300 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=713300
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:193647 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=193647
thingiverse
Customized version of https://www.thingiverse.com/thing:1562501 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1562501