1 4 inch bit organizer 3d models
1269604 3d models found related to 1 4 inch bit organizer.thingiverse
This tray is built for 1/4 inch Pittsburgh Pro socket sets, but may work with other brands.
prusaprinters
This is a bit holder for standard ¼-inch bits. ...The part includes storage for a PB Swiss bit holder. https://www.pbswisstools.com/en/tools/quality-hand-tools/precisionbits/product/pb-845110-30-m
thingiverse
1/4 inch bit holder for modular multi-tool. Holds up to 36 bits (less with snap for .375 OD bit driver). You'll need (2) 1/4-20 x 1.5" screws and (2) nuts. I designed the bit holder and tool snap. ...Multi-tool designed by Gregg Meyer
thingiverse
a small holder for 1/4-inch bits for when the common chunky handles are too big to reach certain places I've printed this with PLA and had to do some adjustment to make the bits fit - my recommendation is heating up an actual bit and forcing it into...
thingiverse
I use lot of different 1/4 drive bits for my power screwdriver. I've gone through lots of bit holderrs also. I wanted one with a tight fit and lots of holes and had a lanard loop. So I test ran a few hole sizes and found one I liked. Instructions...
cults3d
I use lot of different 1/4 drive bits for my power screwdriver. I've gone through lots of bit holderrs also. I wanted one with a tight fit and lots of holes and had a lanard loop. ...So I test ran a few hole sizes and found one I liked.
thingiverse
... bottom of the screwdriver to hold the bits in. The magnet should have a diameter of 6 mm (height 1 mm). AliExpress Link: Neodymium Disc Magnets 6x1mm Keep in mind that a higher resolution than 0.15 mm may result in a press-fit of the hex bits. ...
thingiverse
A simple 48pcs 1/4" hex head bit organizer for wall mounting.
thingiverse
It is a 4 x 15 grid giving you 60 spots for your 1/4" hex driver bits. The two tiers in front fit the shorter bits while the back two rows fit the taller bits. I have uploaded two versions of the model: one that fits each bit snugly and one that fits...
thingiverse
1/4 & 1/8 inch shank router bit holder - 25 holes for each
thingiverse
... first attempt. I drilled the holes all the way through a 3/4 in piece of scrap and added a bottom plate to make it easily portable out of the drawer. Top to Bottom Height is 3/4", Lip is 3/32" in Height - Identical for both 1/2 and 1/4 versions.
thingiverse
This is just a simple bit holder for quarter and eighth inch bits. The hole sizes were made to fit snug enough to keep the bits from falling out but not so much that you get injured pulling them out. 6.54mm and 3.43mm. ...The STL file does not contain...
thingiverse
This is a holder for four 1/4 inch bits. I have printed it with 20% infill and 1.5 resolution. Bits fit in nicely. ...The printer has to be very precious otherwise the fitment can be a little bit off.
cults3d
1/4" Hex Bit Holder/Organizer. Hex key holders are mostly for metric, but I needed an inch/imperial version for the text listing each key size. I found this one had text for most of the sizes I needed. Hex Key Holder (Inch). Then I added some...
thingiverse
Adapter to use "normal" 1⁄4 Inch (6,35 mm) bits on your wowstick. Uses a 2.5x5x10mm magnet to keep both holder and bit in place. ...Also depending on screw there is a magnet effect.
thingiverse
[1/4" Hex Bit Holder/Organizer.](https://www.thingiverse.com/thing:1692958/ "Title") Hex key holders are mostly for metric, but I needed an inch/imperial version for the text listing each key size. I found this one had text for most of the sizes I...
grabcad
Tool bit organizer for 1/4” tool bits. ...It is expandable with extra parts, for if you have a large number of bits.
thingiverse
I bought a precision screwdriver (made for watches and eyeglasses); however it only took 4mm sized bits, so I couldn't use it for larger screws because none of my standard 1/4 inch bits would work in it. I searched for some type of adapter to buy...
prusaprinters
Adapter to use "normal" 1⁄4 Inch (6,35 mm) bits on your wowstick. Uses a 2.5x5x10mm magnet to keep both holder and bit in place. ...Also depending on screw there is a magnet effect.</p> Category: Hand Tools
thingiverse
I saw there were pen holders to replace the router, however I wanted to keep weight of the sled equal to when I was cutting so here is a small 1/4 inch "router bit" pen that can be switched with a router bit and draw on paper. I hope I don't need to...
thingiverse
A router template bushing that fits into the stock baseplate of the Rigid r22002 router. ... Close bit clearance, my templates are pretty tight in places. ...See the a360 link to edit and make your own.
thingiverse
To hold your most actively used tool bits.
thingiverse
I have found nylon to be pretty nice as it gives a bit, but if you live in a humid area they will swell so you might have to oversize them. Also a soft PLA works well. ...I used Amazon basic PLA because that is what I had left for my first print and...
thingiverse
1/4-inch socket peg. ...The OD of the peg top and bottom is 0.23-inches
thingiverse
I had to drill 8mm holes, but I could not get 1/4 inch hex bits, so I made an adapter. 8mm 원형 비트를 홀에 삽입하고, 빈 틈을 글루건이나 본드로 메꾸세요. Insert a 8mm round bit into the hole and fill the gap with glue gun or bond. 가능한 infill 을 높게 설정하여 출력하세요. Set as...
prusaprinters
Toolbox socket organizer for 1\4 inch sockets. The base is designed to accept a 10x3mm magnet as the base is printed at a .2 layer height. I printed all of these on a Creality CR-10S and placed a M25 pause between layer 16 and 17 in order...