1 4 sockets 3d models

... adding a touch of elegance to any room's décor. ...Its robust design ensures seamless performance, boasting an impressive minimum wall thickness of 2.4 millimeters that effectively shields against moisture, guaranteeing unparalleled water resistance.

... tool (http://www.thingiverse.com/apps/customizer/run?thing_id=306072). ...To fabricate this unique design, utilize these specifications: knobHeight of 4.0, knobDiameter of 17.0, nutWidestDiameter of 12.46, nutHeight of 5.54, and ridgeRadius of 2.

http://www.thingiverse.com/apps/customizer/run?thing_id=619626 Instructions Using the following settings: Adjust option is set to 1. Label one height is set to 8.0 millimeters. Label one font style is Orbitron. Label thickness is set at 1.5...

http://www.thingiverse.com/apps/customizer/run?thing_id=615256 Instructions Using the following options: block_brand = LEGO dual_bottom = No vertical_axle_holes = No curve_stud_rows = 5 wing_end_width = 2 roadway_y = 0 roadway_x = 0 block_type =...

This set includes: 1 dragon skull https://www.patreon.com/dragontrapperslodge Join us on Patreon to receive monthly miniatures sets and much more! ...Participate to our polls and give us feedbacks as well as join monthly painting contests.

AKS-74U 1 features an impressive lineup of four models, each equipped with a variety of extra gear and moveable parts, including different types of forends for added versatility.

https://www.thingiverse.com/apps/customizer/run?thing_id=193647 Instructions Using the following options: head_height = 10 nut_thread_outer_diameter = 9.25 type = carriage_bolt nut_height = 7 head_type = flat nut_thread_step = 1.8 outer_diameter =...

Accessible at http://www.thingiverse.com/apps/customizer/run?thing_id=40703, this version boasts a 1-inch iPhone case with build plate selector disabled and features rotated by 179 degrees. ...It has a thickness of 1.8, an overlapping pattern spacing of...

... "Katz-Moses Dovetail Guide," but made it affordable if you own a 3D printer. The design includes slots for 1/2" thick magnets that are 1/8" wide. ... You might need to use a sharp blade to carefully carve out the holes so the magnet fits snugly.

This is a Customized Version of Thingiverse Object #169491, Created Using the Thingiverse Customizer Tool: https://www.thingiverse.com/apps/customizer/run?thing_id=169491 Customized Parameters: Height Adjusted to Maximum Capacity - 10 Ridge Thickness...

Teensy 4.1One of my favorite microcontrollers.Just wish it had better deep sleep and idle capabilities.https://www.pjrc.com/store/teensy41.htmlPlease support Paul since he has contributed heavily into the development of this board and lots of Teensy...

Top/Bottom Thickness Is Also 1.8mm. Infill Infill Density Is 100%. The Infill Pattern Used Was A Grid. Infill Overlap Percentage Is Set At 20%. Skin Overlap Percentage Is Also 20%. Speed Print Speed Is 70mm/s. Travel Speed Is 120 mm/s. Support...

update: Evo 4 included. No swimming pool this week! IDEA was there is open and "denial" versions for the same base. You both will have a bulge. (Actually the "denied one" has more difficulties to hide it which is supposed to be fun and...

Settings: Print Settings Printer Brand: Formlabs Printer: Form 1 Rafts: No Supports: Yes Notes: Make a pretty low layer height and thicker infill since it's so small (about two and half inches long), did mine on a plus version of the Form, so didn't...

Had some 100ft 1/4inch cables with just the plug, no sleeve just leaving the wires exposed. so I drafted this up as a replacement. (using dimensions from a standard sleeve with some added thickness since its plastic rather than steel) Printed with...

The enclosure you see in the photos hasn't been used because I purchased a RADDS 1.5 instead. It's still got none of the two 50mm fans and nearly all the support materials intact. Here are my print settings: Printer Details Brand: RepRap Model:...

... boasts a sturdy construction that withstands regular use. The design has been optimized for ease of printing, ensuring minimal post-processing requirements. Dimensions: 6 inches long x 1 inch wide x 0.5 inches thick Weight: approximately 3 ounces

... I am using a ¼-28 Tap I got from Amazon for about $4. I printed on 0.16mm for the final print, but the drafts were at 0.22 and functioned fine. So if you're in a rush, send it. If you have the spare 2 hours for a nice slow print, also send it.

Hollowtech 2 adapter for a 1/4 socket wrench

Remixed to be a 4-in-1 device, my first remix ever (woo)

The iPart offers table-based customization for sizes ranging from 1/4 inch to 1 1/4 inch. ...It features customizable properties, including Description and Size, to meet your specific needs.

... bolt commonly found on utility boxes like water meters. ...It adapts the 1" 5-sided bolt to a standard 6-sided 1-1/8" or 1-1/4" socket. ... This adapter was designed using Tinkercad and can be edited online at https://tinkercad.com/things/i8A9I2GeL2d.

Customized version of https://www.thingiverse.com/thing:892317 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=892317

This adaptor is designed to fit a Fein Turbo III 2-1/4" hose to a common Shop-Vac 1-1/4" hose for seamless usage. It might also be helpful in other combinations, ensuring a tight fit of the hose. ...Check out this 3D printed vacuum hose adaptor at...

this is a labled tray to hold pittsburgh 1/4" drive torx sockets from harbor freight

pololu 4.4:1 simple draw.

Works for any size socket that has a 1/4", 3/8", or 1/2" drive. Designed so that the base of the socket sits directly on the rail face and slides freely. The knobs are modelled as exactly .25" .375" and .5" squares (every socket in my toolbox is...

Tumb and finger wheel for 1/2 rachet sockets. Use when you finger tight or loosen screws with socket. Sit only with friction in socket. ...

Slot measures 1/4 inch by 4 inches in size

Tubular Rectangular Pipe 4 x 1 3/4"