1 4 to 4mm bit adapter 3d models

This object replaces the factory Felder rectangular fitting that is for an 80mm round port with a US standard 4" hose fitting. Uses the factory mounting screws. Recommend printing with the 4" round sitting on the build plate. I had no issues without...

... cost more than $10. I ended up sourcing the PVC threads from McMaster and the garden hose threads from a link on Thingiverse. To clarify, this is a female 3/4" GHT (Garden Hose Thread) fitting that converts to a male 3/4" NPT (National Pipe Thread).

... two couplers to make it possible. ...The new adapters fit seamlessly into my resin printer, but I needed to scale up the DLP design by 9% to account for its inconsistent print size. ...After adding a flexible rubber O-ring, everything works flawlessly.

GoPro Mount adapter (male and female) to 1/4" UNC camera mount with a hole for ruthex threaded insert 1/4-20x12.7 Compatible to modular mounting system (ModularMounting) Fusion360 and STEP files included. ...Modifications welcome :)

GoPro Mount adapter (male and female) to 1/4" UNC camera mount with a hole for ruthex threaded insert 1/4-20x12.7 Compatible to modular mounting system (ModularMounting) Fusion360 and STEP files included. ...Modifications welcome :)

Design: Modified DIY Bench Vise Version Customized from thingiverse.com/thing:97238 Created with Customizer at thingiverse.com/apps/customizer/run?thing_id=97238 Settings: Setting inside Vacuum to 64 units Setting outside Bandsaw to 98 units Raising...

No hardware store carried a direct 6 in to 4 in reducer, so I designed this and printed it out of PETG!  Printed with 0,8 mm nozzle, two layers thick.

Is light passing through the wavy gap between your netcup and your 4-inch PVC pipe? Have I got a solution to all your problems? No, I don't have any solutions, but I can assist with installing a netcup into the 4-inch PVC pipe. ...Maybe next I'll add a...

Modify the design to reduce support amount Print Settings Printer: Creativity Elf Core XY Rafts: No Supports: Yes Resolution: 0.16 Infill: 25 Filament: Generic PETG Notes: Increase Support Overhang Angle to 70° to avoid support on the 20/27 (3/4")...

I made this for my car so that an "Airaid" air filter with a 6" intake diameter opening would mount to a 4.5" air intake tubing / inlet pipe. ... I used MeshMixer to ad 45 degree latticing in the hollow center for support as it prints.

... sized D-mount lenses will work with it since the lens effectively sits inside the camera, leaving extremely limited space available. ...The source files are included if anyone needs them to start building an accurate model of a Micro 4/3rds mount.

120mm fan duct for 4 inchs pipe Create with Fusion 360 Create by Unix1

The minimum bottom gap allowance is currently set to 1. 6. The maximum height setting for each part comes out at 141 units tall. 7. Hole depth is established at 20 units down. 8. ...The margin of the model parts are configured at a setting of 30 tenths...

This setup enables seamless integration of the Rockler Dust Right system directly into 4-inch Schedule 40 PVC piping.

Hopefully final version: Rather than employing a DWV sewer pipe, this design utilizes a 1/2-inch-thick wall pipe, relying on minimal infill material to achieve a lightweight structure. This combination should result in a stiff and lightweight overall...

(Note - full size version is printing now and should be just fine as far as edges are concerned, so I'll publish it here tonight before things slip my mind.) I made this holder to hold all of my drive bits in one spot within my toolbox. The way it's...

I'm running 2 Noctua Redux-1700 PWM fans between 6 and 7.5 volts and it manages to push through 2 draft blockers (Canada Woo!) and about 25 feet of 4 inch ducting (with 3 elbows and 2 bent flexible ducts) with ease. I've included 2 high quality...

Extend your vacuum's reach by adding inexpensive 3/4" PVC piping. ...Reach previously inaccessible areas with the addition of clever sweeping elbows that expertly navigate tight spaces.

Here is a temporary fix for the problem. ...I transformed a 4mm filament tube into a 6mm tube to get around the issue with my regular tube being destroyed by the extruder gear during filament removal.

Modify the design to reduce support amount

... that great. So i reduced the 10mm holes to 4mm bei inserting this little thing. Also i designed one inlet without an inner hole for closing up some 10mm holes as i drilled to many of them. For buildplate-adhesive it needs a brim of 4mm. ...

Who among us hasn't needed to repurpose their bathroom vent as an impromptu fume hood when time is of the essence?\r\n\r\nTake a few minutes to edit your SCAD file if the fan and mount combination isn't quite right.\r\n\r\nIn my case, I had to...

To ensure smooth printing, I carefully designed the transition from rectangular to circular, allowing even basic printers to handle the slope without any issues with supports. Using PETG with a 25% infill and five perimeter layers was overkill, but...

It's slightly asymmetrical top to bottom as on my laser it's a 35mm distance from the bottom ledge to the bottom of the opening on the back of the machine. Print Settings Printer Brand: MakerGear Printer: MakerGear M2 Rafts: No Supports: No...

Print Settings: Printer: Felix 3.1 Dualhead Rafts: No Supports: No Resolution: 300um Infill: 5% Notes: Taking approximately 16 hours to print requires a slightly higher temperature than smaller objects. A nozzle temp of 210C (PLA) and table temp of...

Below are the project settings: Instructions for Using these Settings: Setting hole_tolerance_percent to 5% Setting hole_depth to 13 units Setting max_h to 145 units Setting floor_thickness to 2 units Setting vgap_tenths to 70 Setting num_total to...

http://www.thingiverse.com/apps/customizer/run?thing_id=822726 Instructions Using the following options: hgap_tenths is set to 8 tenths of an inch vgap_tenths is set to 7 inches, a significant distance num_total is a total number of items, set to 90...

Using the following settings: - Hole Depth: Set to 12 mm - Hole Tolerance Percent: Set at 5% - Maximum Height (Max H): 218 mm - Vertical Gap Tenths: 15 - Floor Thickness: 2 mm - Number of Units Total (Num Total): 80 - Margin Tenths: 75 - Horizontal...