1 75 roll bar clamp 3d models

These are 1.5" and 1.75" roll bar clamps that can be used for a variety of tasks. In my case, I have a set of Pro-Armor harnesses in my Polaris RZR. These harnesses attach behind the seat by wrapping around the roll bar cross-member. Other...

The caps use a 7mm (actual diameter) or 1/4" Nominal Diameter o-ring made from bulk o-ring stock or you could just print one from TPU. The o-rings are a very tight fit so you will need to lubricate them with silicone or some other PLA safe lubricant....

This fits around a 38mm or 1.5in roll cage or roll bar tube and holds a standard GoPro mount. ...It is designed .25mm small to allow for clamping force and has space for M4 hardware to fasten it.

1.75 Roll Bar Mount for Blackvue Camera DR750X model

http://www.thingiverse.com/apps/customizer/run?thing_id=62800 Instructions Using the following options: gopro_bar_screw_shoulder_th = 4.5 gopro_bar_screw_d = 3 gopro_secondary_what = clamp gopro_captive_rod_angle = 45 gopro_captive_protruding_h = 0.5...

Decide on proper dimensionality using Gopro Bar Thickness measured carefully with precision, setting the mark for perfect performance with an impressive value of 3.2 millimeters as accurate results achieved always require perfection which is...

In this radical reworking of the roll bar clamp, several crucial modifications were made to bolster its overall structural integrity in critical areas. I first modified one version, then cleverly mirrored it to create distinct left and right...

These blocks are designed to work with a fairly standard 1.75 inch roll bar clamp available on eBay. The version shown in the object photos was printed in PETG at .2 layer height. NOTE: These mounts may not fit your application in an off-the-shelf...

General-purpose Utility Task Vehicle roll cage mounting system specifically designed to accommodate 41-millimeter diameter bars.

This object was crafted using Tinkercad; modify it via their online platform at https://tinkercad.com/things/lflUMtkT4Su. ...It features a simple print-out design, and securing wire grouping to a roll bar is achieved through the use of a zip tie.

After several Whoop crashes and numerous destroyed canopies, I decided to design an internal roll bar to prevent the thin canopy from collapsing during impacts. This roll bar was specifically designed for the BetaFPV Beta65 and Beta75 models but may...

Base geometry copied from mmotley's clamps. ... Improved for strength and ease of use.

The specifications for this model include a gopro_captive_rod_angle of 45 degrees, a gopro_captive_protruding_h of 0.5, a gopro_ext_len of 50, a gopro_bar_screw_shoulder_th of 4.5, a gopro_rod_nut_od of 8.05, a gopro_secondary_rotated of 0, a...

To print this GoPro mount, use the following options: gopro_captive_protruding_h = 0.5; gopro_bar_screw_d = 3; gopro_primary = double; gopro_bar_th = 3.2; gopro_bar_gap = 5.0; gopro_bar_screw_head_d = 6.2; gopro_bar_rod_d = 45; gopro_rod_nut_od =...

... install. ... Includes the top (go pro mount) and bottom(to protect roll cage) with slide through slots for the hose clamp. I printed my final ones PC-MAX. ASA and Nylon seem to do just fine as well. ...(the model should account for any shrinkage.

The user created this Gopro clamp using ProDesktop for the Greenpower Kitcar, designed to fit snugly above the driver's head on the rollbar's right side. This design allows for easy access to the back of the case even with an extra battery pack...

This is a tube clamp for a 1.75 tube. It is very similar to a tube clamp for a rouge Fab M600. The print allows you to insert a nut and run a bolt through it to lock it down. I have a regular version and one that has been elongated to glue a...

A 12v light mount for a 1.75 in roll cage. Uses a standard worm drive clamp to hold it into place. ... Light was from broken Kobalt air compressor.

Designed to be mounted to a 1" OD roll cage that is at a 45 degree slant. I used 3 of them on my roll bar. Print the piece out and go to a hardware store to find the correct bolts, or screws to use. Simply force them into the piece to cut the...

https://www.larsonelectronics.com/product/265/bar-clamp-mount-for-permanent-mount-and-magnetic-mount-spotlights-bc-1-7-8-1-75-diameterMade in the USAHeavy duty aluminum bar clamping system that enables owners of vehicles, heavy equipment and boats to...

https://www.larsonelectronics.com/product/265/bar-clamp-mount-for-permanent-mount-and-magnetic-mount-spotlights-bc-1-7-8-1-75-diameterMade in the USAHeavy duty aluminum bar clamping system that enables owners of vehicles, heavy equipment and boats to...

Filament Roll clips: 3 mm width (e.g. Hatchbox), 3.6 mm width (e.g. ...Overture), 5 mm width (e.g Coex).

USB dongle roll bar clamp for AEM ECU

This clamp was designed to work with the 1" vertical shaft on my tripod as a means of adding 1/4-20 attachments. My primary intention for the design was to add an iPad mount to use for a teleprompter. The hardware required to complete this build: (2)...

Revise 1.75in Roll Bar Camera Holder Designed for BlackVue 2 channel dash camera

Double Roll bar sized for M3 mounts

1" roll bar ice chest restraint specifically designed for the Honda Pioneer 500 cargo area. Four restraints are clipped to the roll bar and secured with zip ties. ...one inch strap and buckles complete the assembly.

... for a 1.75in bar. ...I use this to mount my GoPro to the roll bar in my Miata. This is sized to take standard metric nuts rather than the slightly larger gopro nuts. Narrow enough to fit in the center of a Hard Dog Hard Core double diagonal roll bar

Roll bar for Jeep Comanche ABS bodywork (Aliexpress) Printed in three parts to be assembled. ... Drill 4 holes of 2.5mm in the body to fix the roll bar.