1 8 npt to m10 3d models
3606978 3d models found related to 1 8 npt to m10.
thingiverse
This is a customized adapter for connecting a 3/8“ UNC 16 threaded camera light stativ to a M10 hex screw nut, where I attached a lampshade. ...The adapter fits extremely snugly and provides sufficient rigidity to securely hold my lampshade in place...
thingiverse
Connector for air compressor and silicone hose used in my Zbaitu laser machine. ... Better if PetG. But PLA and ABS work Enjoy V.1: https://www.thingiverse.com/thing:5403599
thingiverse
I decided to install my bidet in a convenient location, attaching it directly to my garden hose for easy access. ...Fixing it out back proved to be a great idea, as the outdoor space provided ample room to work comfortably.
thingiverse
This DIY hydroponics manifold connects seamlessly to any standard 3/4-inch submersible pump, delivering a superior flow rate compared to traditional linear manifolds. ...I successfully completed my maiden Fusion 360 project with this innovative design.
thingiverse
I needed to drain my irrigation system and I have access to a spout that's a male garden hose thread (3/4 BSP) and adapted an air hose end to make this easy. Please see verify your system to see how much PSI you can run through it. ... I ran each...
prusaprinters
Before winter comes, It´s mandatory to blow the water out of the watering system, and I needed a good adapter to do this easy. Adapter printed in PLA, and washers printed in TPU. Supports recommended.
thingiverse
... hoses and valves, users must apply an abundance of Teflon tape to prevent leakage issues. ...For optimal performance, individuals can also smooth out the interior surface to accommodate a hose gasket, significantly enhancing overall functionality.
thingiverse
I'm modifying this setup for my RV, adding a garden hose adapter to the exterior shower hose so I can connect an outdoor Fillet Table with a sink and faucet. The total cost is $0.48. ... Print Settings Printer Brand: Printer: Prusa i3 Supports: Yes ...
thingiverse
Convert a mine-paw or maxi-paw sprinkler to a small pop-up without digging by reusing the original's groove for an o-ring. ... Ensure the print is upside down, with external threads facing upwards, and incorporates support for stability during the...
thingiverse
Adaptor converts 1/8'' and 8/32'' sizes seamlessly without threaded fastening.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1427458 Instructions Using the following options: hole_shape = 0 spacer_style = 3 generate_handle = 0 generate_screw_hole = 0 pressure_angle = 20 backlash = 0.1 mod = 2 angular_spacing = 75...
thingiverse
Made a nozzle to clean nozzles that spray chemicals for metal etching. No I have NOT tested the chemical vs material. But in terms of PSI, the nozzle seems to hold up at 40psi. ... Recommend to rotate so threads print first.
thingiverse
Needed a sump pump adapter so I could connect it to my garden hose. Going to experiment with this. ...Not sure if it'll be sturdy enough but will see
prusaprinters
Lost the ½" NPT bolt to attach trays to a Droll Yankee brand bird feeder. Thanks to maverickagm for the original post for providing an easy starting point. I printed in PETG, 40% infill, 0.15 resolution to try to get...
thingiverse
The UD (ultra deluxe) version has 1/8" holes to place 1/8" rods through to strengthen the part from snapping or delaminating. I'm using 1/8" drill bits and cutting them to size. If you heat the rods up first they're easier to push through (stove,...
thingiverse
A simple adapter for the Adam Savage work light that allows it to drop into a 5/8" bench dog hole.
thingiverse
Banggood: https://goo.gl/ZXgx3A Gearbest: https://goo.gl/FfE59f Aliexpress: https://goo.gl/bQLi15 Printer: Anet A8 Rafts: No Supports: No Resolution: 0.1 Infill: 100% Notes: I printed it with a 0.4mm nozzle and set the extrusion width manually to...
cults3d
It takes a PC4-M10 pushfit, like the one on the Chinese E3D bowden version, and screws onto a M6 thread of the MK7 (MK8) extruder. I'm not sure if it will be strong enough. The weakest point is between the M6 thread and the M10 section. For the long...
grabcad
A 1/4-inch NPT sized manometer measures up to 63 millimeters and is capable of reading pressures ranging from zero to forty bars.
thingiverse
Simple 1/2" npt plug that I used to block off a pipe on a structure (didn't old any pressure)