1 inch tunnel plugs 3d models

THESE ARE 1 INCH SKULL PLUGS DESINGED IN TINKERCAD

These are smaller that 1 inch so they can be inserted into 1 inch silicon plugs (gauges). ... Made them this way for a few reasons: the silicon is more comfortable the grooves in the print might harbor bacteria the paint/finish won't...

These are smaller that 1 inch so they can be inserted into 1 inch silicon plugs (gauges). ... Made them this way for a few reasons: the silicon is more comfortable the grooves in the print might harbor bacteria the paint/finish won't make contact...

Standard 1.25 in Button Pugs. Use safe material for skin. Enjoy! ...Message for custom designs. 

this thing is a 1 inch ear gauge with the horde emblem have not printed yet but sliced in cura and looks great

These are solid and hollow tunnels or ear plugs of size 10mm

It's hard finding low priced plugs past 50mm, so I made these. If there's any demand for bigger sizes, I can put them on here too. ...I have models made up to 75mm.

There are both 1/2-inch and 3/4-inch versions as well as versions that include a hex thumb screw for easy tightening/loosening (which I highly recommend--who wants to carry around a huge flat-head screwdriver just for plugs?). Note: I highly...

There are both 1/2-inch and 3/4-inch versions as well as versions that include a hex thumb screw for easy tightening/loosening (which I highly recommend--who wants to carry around a huge flat-head screwdriver just for plugs?). **Note:** I highly...

There are both 1/2-inch and 3/4-inch versions as well as versions that include a hex thumb screw for easy tightening/loosening (which I highly recommend--who wants to carry around a huge flat-head screwdriver just for plugs?). Note: I highly...

There are both 1/2-inch and 3/4-inch versions as well as versions that include a hex thumb screw for easy tightening/loosening (which I highly recommend--who wants to carry around a huge flat-head screwdriver just for plugs?). Note: I highly...

Here I have tunnels/plugs to embellish your ears. I created two variants: _V1 is smooth. _V2 is rounded. I really like them both and have therefore printed both versions. I would be interested to know which version you like better? I started...

<p>Did a simple resize and hollow of the blank gauge, printed and measured with calipers. ...Print both or use Microsoft 3D Builder or Meshmixer to split them.</p> Category: Earrings

Did a simple resize and hollow of the blank gauge, printed and measured with calipers. ...Print both or use Microsoft 3D Builder or Meshmixer to split them.

What: Press fit (no glue required) flexible hole plugs for 1 inch 25mm holes. Files for material thickness 1.5mm, 2.0 mm, 2.5 mm, 3 mm, 3.5 mm, 4 mm as different coolers and sometimes different locations on a cooler have different material...

We often make curtain rods from 1/2 inch gas pipe. You can cut the pipe to length and it usually doesn't need a center support. The plugs can be pounded into the cut end of the pipe to allow you to screw on a finial. The STL file is for a finial...

First tunnel I've made myself. ...Hope it's enjoyed :).

... Infill: 10% Notes: Did not use a raft, but I did use a brim. Wall thickness 1.2mm (for strength)

Another tunnel portal. Print in the upright position, top down. ...Supports not needed.

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: cursor = 90 margin = .1 weight = 9 groove = 1.25 edges = 1 $fn = 50 diameter = 25.65 type = 1

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: edges = 1 weight = 10 cursor = 90 margin = .1 diameter = 25.65 groove = 1.25 type = 1 $fn = 50

... Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44815 Instructions Using the following options: weight = 11 edges = 1 margin = 0.1 type = 1 $fn = 50 diameter = 25 groove = 1 cursor = 100

This is a plug for a 1 in hole v3 and V4 plug is a deeper plug

These Plugs are resin Printed. Be carfull that after printing the parts are fully dry. If not it could damage your pinball. Clean and blow out and cure rigth. ... these parts can be brintet on the buildplate you only need to use the rigth side ...

Test tunnel Francorchamps

Tunnel plug. ... 6cm diameter.

Normal tunnel Plug for play

Plug for a 1/2 inch hose, quicker to print than go to the store. ... Freecad spreadsheet or scale in your slicer to resize.

Tunnel

Check out my other goodies at Makersteve.com I was missing a few 1/2 inch wood plugs for the old Futon so I ginned these up. They will work fine for anything 1/2 inch. Great for wood working. Since my Shelf pegs...