1 plus 3 phone case 3d models
1463300 3d models found related to 1 plus 3 phone case.thingiverse
I wanted to 3d print a phone case, but couldn't find the model for my phone. ...i created this model for that purpose.
thingiverse
This is a protective case for the phone one plus 3 with the name mathew varghese engraved in the back
thingiverse
BLU XI Plus phone case. ... Designed for TPU July 18, 2019 update: slightly enlarged hole for charging port.
cults3d
A case designed to fit the Motorola Edge plus. ... Inexpensive print. I've dropped my phone several time with this case and it survived undamaged. ...The case itself will crack but at about a 1$ for the print it's a quick replacement.
cults3d
Phone case for the Moto G8 Plus. Modeled in detail and tested for TPU printing, laying down without supports. ... Includes Soft functioning volume buttons
thingiverse
This cover is a remix of this case for the SKR 1.3 https://www.thingiverse.com/thing:4315249 I made a new cover for the case board SKR V1.3 Anet A8 Plus. It prints faster, looks better, needs less filament and provides better heat exchange. If...
cults3d
Motorola G6 Plus Phone Case I can safely say that it is the best mobile phone I have ever had. ... Added stl V2 with greater protective angle( last image )
thingiverse
Single or double layer Galaxy S21 PLUS phone case. Base layer can be used alone made with any normal filament, or optionally printed in TPU with a harder filament "shell" layer over top to make the case more impact resistant. I used a purple TPU...
thingiverse
This case houses a shelly 1 plus (probably will work for other shelly devices with the same form factor, haven't checked). Intended to be used with a regular 3-core 1.5mm wire and a 3-pole wago plug to connect earths. Needed to have a shelly device...
thingiverse
-Update(30,09,2018): -Deckel.stl are modifed now for a Nice fit -Case.stl are modifed for the hotend cabel I bought my Anet for three months ago and i keep it still upgrading, the original board with the stepper drivers was to loud and the Print...
thingiverse
This case has the space to carry 2-3 cards behind the phone. I printed it in flexible TPU and it never slips off. I'm very pleased with the outcome of this project. It only took about 10 prints to get the sizing just right. ...(Ok, so I'm a...
prusaprinters
But spring loaded doors can close and hit you in the face, pencils can roll away, and phones never stand up on their own.Solve all these problems at once with the Handy Automated retaiNing Kontraption (H.A.N.K. ...for short) so that you can work on the...
cults3d
I created this Universal Phone and Tablet stand 2022 in 3 sizes as I needed it. So will share it here as well! The smallest is 50 x 50 width x 75 mm height Middle one is 60 x 75 width x 85 height The biggest is 80 x 75 x 100 height I created a...
cults3d
This is a phone case for galaxy s8 plus. It is designed with little bit of decoration on the backside of it. ...Enjoy :)
cults3d
This is a phone case for galaxy s8 plus. It is designed with little bit of decoration on the backside of it. ...Enjoy :)
cults3d
This is a phone case for galaxy s8 plus. It is designed with little bit of decoration on the backside of it. ...Enjoy :)
thingiverse
This thing was made with Tinkercad. ... This is a i phone 4/4s case that has a number 3 on it.
thingiverse
A dual layer phone case for the One Plus One. ...Use a hard filament for the outer layer and a more flexible filament for the layer on the inside.
thingiverse
A case design for my Pixel 3 that has a built in hinging cover. Print it as one piece, flat surface down. ... When open, case also acts as a stand for phone.