1 to mm 3d models
2606224 3d models found related to 1 to mm.cults3d
... parts. ... It has stages from 1 to 10 mm by going from 1 to 1 Very practical for a body builder, carpenter, upholsterer etc... ... Personally, I printed it in white and went over with a black permanent marker with a tip at the bottom of the numbers.
thingiverse
i need this reduction to connect a small hose to a circulation pump. ...it becomes a water cooling system for my welding machine.
thingiverse
Guide to drill exact 90 degree hole toward a flat surface. ... 1,2,3,4,6,8,10 and 12 mm
thingiverse
I wanted a tower to test up to 7mm of retraction i made one similar to the one in Cura
thingiverse
... of an existing object so that you immediately see the diameter. **** The size of the compartments in the storage bin is + 0.2 mm. 35.2 x 3.2 mm If your printer cannot print accurately, scale to 101%, otherwise the tools are too tight. ... ****
prusaprinters
Deckel mit jeweils 3 Unterlegstücken je größe.Material: PLASchichtdicke: 0,2mmFüllung: 25%Farbe: nach BeliebenStückliste:1 Stück Box_Unterlegplaettchen_V02.stl **1) **2)1 Stück...
thingiverse
A collection of 20 different all purpose, ready-to-print tweezers from pretty small (80 mm/3.1") to pretty big (160 mm/6.3") with narrow and wide tips for scrap filament removal, sorting screws, soldering, handling small electronic components... and...
thingiverse
A collection of 20 different all purpose, ready-to-print tweezers from pretty small (80 mm/3.1") to pretty big (160 mm/6.3") with narrow and wide tips for scrap filament removal, sorting screws, soldering, handling small electronic components... and...
thingiverse
... of an existing object so that you immediately see the diameter. **** The size of the compartments in the storage bin is + 0.2 mm. 35.2 x 3.2 mm If your printer cannot print accurately, scale to 101%, otherwise the tools are too tight. ... ****
thingiverse
A box for every drill bits from 1 to 5mm, per increments of 0.5mm. I printed with PETG in my case. Indeed this box goes around in the shop, so it ensures good chock resistance as well as chemical resistance. ... Note: the cover is intended to be...
grabcad
This Tool be used for draw a circle without compass Cette outils de dessin est utilise pour tracer des cercle sans le compas
cults3d
Following the installation of a glass plate Wisamic Thermal Bed 3mm in transparent borosilicate glass, I had problems detecting the bed, I also added aluminum foil under the glass plate.
thingiverse
... ring such as this one. You need to adjust the inner and outer diameter of the ring for your fitment. Dimensions are for an AEZ (CB 60.1 mm) wheel on a 2008 Prius hub (54.1 mm). ... I uploaded a new .stl version named *_High with better quality.
thingiverse
I've lost one of my rings during the winter and didn't want to buy a new set for the summer wheels, so I just modeled it according to the remaining ones. Coincidentally, it did fit well on another one of out family cars. I've used it on an 2001...
thingiverse
... if you need different thread or garden hose size, i can make several version of this thing. UPDATES : 07/05/18 : 1" BSP washer added 23/05/18 : 1p_BSP_male_to_3_4p_BSP_female_90.stl added (requested) 22/06/18 : 1p_BSP_to_38mm.stl added (requested)
prusaprinters
Several designs of a reducer nozzle, 7 to 1mm, and an angled joiner reducer, 7 to 4mm, for a University Project for an Unmanned Firefighting vehicle.Threaded reducer nozzles are made for M4/5 Irrigation Nozzles.Long Nozzles are approx. 28mm without...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=158717 Instructions Using the following options: output_units = Metric inline_junction_type = round input_size = .5 strength = 1.0 input_units = US vault_connector_ratio = 1.8...
thingiverse
Simple, quick and dirty adapter from 33,24 mm thread on pumps side to 25 mm inner diameter hose.
thingiverse
I created this spacer to mount my usb charging port to my handlebars since all the good mounts that I've found so far are for 1" bars and my old Kawasaki KZ305 has 7/8" bars. The mount I was inspired to remix this from is probably one of the...
thingiverse
G 1/2 to 12 mm (inside) hose connector at a 90 degrees angle. ...Print with high density and use only in stationary applications (hydrophonics)
prusaprinters
... than a couple of days - after that, some keys will just slip out. Depending on your X/Y step and flow calibration, you might need to scale this print up or down by 1-2% for a perfect fit.Recommended settings:Layer height 0.2 mmLine width 0.42 mm
thingiverse
... together. Gaps & Tolerances .1mm should be a tight fit for an FDM printer. May have to press with force .2mm should usually slip together fairly easily maybe with slight force .3mm may feel some wiggle. ... .4mm probably going to feel loose
thingiverse
Test to see how well your filament allows light through close and far. Can test with different layer heights and materials. ... the print has 0.2mm, 0.4mm, 0.6mm, 0.8mm and 1mm Used for this project https://youtu.be/Xyod39A879Y Other Files 3D...
thingiverse
... constant wall thickness in the X-Y plane and be an even multiple of 0.40mm line width to minimize retractions and eliminate the need to fill gaps. 2. It be snappy and firmly hold my 1.75mm filament to all my filament rolls. 3. ...It be pretty.
thingiverse
I needed a 1 1/4" to 50 mm hose adapter and ended up with this design. You can save some significant printing time if you set the infill pattern to "concentric". I also created a 50 mm Adapter with flange. Check my other tings if you have a need...
prusaprinters
A simple model to test different wall thicknesses. ...The thinnest wall is 1.0 mm and it goes up to 2.0 mm in 0.1 mm steps.