1 tube clamp 3d models
951069 3d models found related to 1 tube clamp.thingiverse
A 2-Piece print. I've printed and used a number of these with PLA. ... A new version is coming soon with a hinge on one end.
prusaprinters
use for 1.25" tubes, hardware is 1/4". one side has counterbore for socket head cap screw if you want to mount something on a stud. the other side has a hex bore for a captive nut. this lets you choose which side of the screw you want to use to mount...
thingiverse
This is a simple clamp I designed for running 3/16 diameter brake lines along a 1 1/4 Inch tube frame in a DF Goblin kit car.
thingiverse
... tube. ...Uses standard 1/4-20 nuts. It will obviously melt on a muffler but may have other uses as a tube clamp or mounting surface on 1" OD pipe or tube. I was very suprised at how strong this clamp is printed fully filled. ...3D print with support.
thingiverse
This little thing can be built in for clamping the PTFE-tube that leads to the extruder of a Voron 0.1. When you load or unload and need top push or pull hard, the tube may come out of its position. I did not want this, so I designed this. ... Works...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=909819 Instructions Using the following options: clamp_bolt_diameter = 4.5 clamp_contact_thickness = 10 mount_rotate = 90 clamp_bottom_hole_style = 1 gopro_buckle_notch_width = 3.75...
thingiverse
This is a tube clamp for a 1.75 tube. It is very similar to a tube clamp for a rouge Fab M600. The print allows you to insert a nut and run a bolt through it to lock it down. I have a regular version and one that has been elongated to glue a...
thingiverse
Made to clamp 2 pieces of 1-1/2 square steel tube together and has holes to mount a metal bracket to hang my milwaukee drill from.
thingiverse
G27 Shifter clamp adaptation for a 1 inch square steel tube
grabcad
Ferrule, 1.00Inch Clamp Tube OD, w Seal Groove
grabcad
Ferrule, 1.50Inch Clamp Tube OD, w Seal Groove
thingiverse
This is a lot of 1/2" Pipe Clamps for modeling or small woodworking projects. They use 6mm or 1/4-20 bolts to tighten to the pipe. There are many shapes and sizes for many applications. My other clamps were too big or too small, so I made some to...
thingiverse
Customized version of http://www.thingiverse.com/thing:232920 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=232920 Instructions Using the following options: S = 1.2 M = 5 T = 5 R = 1.315
thingiverse
This is a small hose clamp made to connect standard 1/8" ID aquarium airline vinyl hose to a 1/8" barb fitting. I make RC aircraft and do a lot of vacuum bagging. My normal pulls are in the range of about 22 to 24 inches of mercury and the...
prusaprinters
This is a small hose clamp made to connect standard 1/8" ID aquarium airline vinyl hose to a 1/8" barb fitting. I make RC aircraft and do a lot of vacuum bagging. My normal pulls are in the range of about 22 to 24 inches of mercury and the aquarium...
thingiverse
You will need to purchase (if you don't have any extra on hand) new 1.75mm PTFE tube paths from E3D so that you can put a longer one in to bring it to the end of the clamp - it will slide inside of the other larger bowden tube when tightened. You...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=28400 Instructions Using the following options: hotend_holder_width = 19 hotend_diameter = 13 hotend_screw_diameter = 4 zipties_depth = 2 bowden_jaw_top = 12 zipties_width = 3...
thingiverse
Securely mount brake lines on your automotive project with these clamps for 3/16" (4.75mm) and 1/4" (6.35mm) tubing. The tubing is designed to snap in tightly and attaches with an M4 or similarly sized screw. ... Print with 1.2mm perimeter width and...
grabcad
Semi Realistic 3D model of Light Duty 1,5" Mini 360 QR Clamp for 40mm Tubing from AliExpress
thingiverse
Customized version of https://www.thingiverse.com/thing:909819 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=909819
thingiverse
I've been helping some friends build a restaurant, and had to 3D print brackets for an ice machine's 1/4" water line tube. ...I added two holes on the bracket but only ended up needing one.
thingiverse
This model uses the following hardware: 3/8" - 4" Eyebolt 3/8" - hex nut (4) 1/4"-20 - 1.5" Bolts (4) 1/4"-20 - Hex Nuts or Hex Stop Nuts (4) 1/4"-20 - flat washers Foam rubber shelf liner is wrapped around the tube to prevent scuffing and to...
thingiverse
This model uses the following hardware: 3/8" - 4" Eyebolt 3/8" - hex nut (5) 1/4"-20 - 2" Bolts (5) 1/4"-20 - Hex Nuts or Hex Stop Nuts (5) 1/4"-20 - flat washers Foam rubber shelf liner is wrapped around the tube to prevent scuffing and to increase...