1 x 1 rubix cube 3d models

I'm Sabot base to stand 8 figures mounted on UK 1 pennies that are 20.3mm in size. Example units show how they fit perfectly. You can also cut magnetic sheets into 1p discs and stick them in so the penny bases stay firmly in place. ... I've kept the...

Simple model: 1/2x13 nut as weights, 4.5mm/0.177" inner diameter hole. I used some 550 cord without the inside guts in for this.This did take a little bit of clean up before it worked well. ...I printed this using PLA+ at 100 percent infill, and ended...

SKR PRO V1.1 Board Update with TFT 24. I upgraded to an SKR PRO board as the original one was too loud. It's usually controlled via Repetier server, so I only gave it a small display since navigating through buttons works much better for me. The...

Minimalist sabot base to stand 8 figures mounted on UK 1 pennies (20.3mm) Example units on the bases to show how they fit. You can also cut magnetic sheets into 1p discs and stick them in so the penny bases stay in place. I've kept the bottom of the...

Spec: 1-3/4 inches tall by 3/4 inches wide Sized and profiled as best as possible to original millwork Printed with my X1-C with a .6 nozzle using ASA filament. I used the Bambu slicer to create 4 pieces and then used the cut feature to create the...

The dollhouse itself will be built on a precise 1:12 scale to ensure accuracy and authenticity. I sourced the Eames Chairs from kspring to perfectly complement the custom-made dining table. The intricate design of these iconic chairs is a perfect...

This particular design is tailored for a 1/4-20 bolt, which you'll need to screw through the plastic, past the threaded area, to secure it in place. That way, the screw won't fall out when you remove your camera. ...I printed this plate with PLA, but I...

A speaker stand for a horizontal alignment of two Logitech speakers from a 5.1 system. One holder combines both front and rear speakers and elevates them roughly 2.3cm above floor level. The sleek horizontal design of the mount enables positioning of...

Here is a unique design element used to attach a 1 inch OD pipe directly into the base of an eight by ten oval dome shape that commonly features in designs for skylights or oval picture frames. It contains one threaded hole that allows users to screw...

Assembly of a 2.5x2.5 Step Motor on an Aluminum Profile 1.5x1.5

The model is 1/60 scale, but if you set your printer to print at 85%, it should work for 1/72 scale, as shown in the attached picture. To assemble both sides of the main wing, you'll need to duplicate and mirror it. Same goes for all other parts. The...

This is a pair of brackets for mounting the Meanwell LRS-350-12 securely to a MendelMax 1 or 1.5. The brackets fit snugly between the two horizontal 2020 extrusions on the base of the MendelMax, keeping the PSU safely away from the frame. I'm...

... The model is 1/60 scale and if you set your printer to print at 85%, it would work for a 1/72 scale, I believe, please see the attached picture for reference. The main wing needs to be duplicated and mirrored, or it won't look right on both sides.

Size: 1.5 ft x 1.5 ft (45.7 cm x 45.7 cm) After downloading: use this digital file to order a print from the printing service of your choice.Looking for another size or design? Check out our twelve other sizes of this same theme, or browse our other...

It is designed for 45 Colt, 1.000" (25.5 mm) bullet length. It was designed for my printer so you may adjust the slicer if yours prints smaller or larger. The hole on the side is for small machine screw to attach the spring to. For ease of operation...

What it does is convert a 3/8-inch NPT thread into a hose with a 1-inch ID. I created two types of adapters: one has a single barb and the other has three. Each one comes in both solid and hollow versions. The solid version might be useful if you...

I wanted to transform my XYZ Davinci 1.0 into a dual extruder with auto bed leveling. I swapped out my controller for an MKS Gen V1.4, acquired a Chimera clone, extra motor, and BLTouch. The challenge was ensuring that this upgrade wouldn't...

The bottom edge sticks out by 1/4 inch to improve lateral stability. Print Settings Printer Brand: Printrbot Printer: Simple Black Rafts: Yes Supports: No Resolution: .2mm Infill: 80% Notes: Make sure the raft is securely attached and flat, as...

Sabot base to stand 10 figures mounted on UK 1 pennies (20.3mm). Example units on the bases demonstrate how they fit together seamlessly. You can also cut magnetic sheets into 1p discs and attach them securely so the penny bases remain in place...

It is designed for 45/70, 1.000 (25.5 mm) bullet length. It was designed for my printer so you may adjust the slicer if yours prints smaller or larger. The hole on the side is for small machine screw to attach the spring to. For ease of operation...

Minimalist sabot base to stand 6 figures mounted on UK 1 pennies (20.3mm) Example units on the bases to show how they fit (didn't have my celtic slingers finished). You can also cut magnetic sheets into 1p discs and stick them in so the penny...

This is a 1:420 scale model of the Quasar Fire II light carrier. This ship was depicted in the Star Wars Rebels series, as well as the Star Wars Squadrons video game. The exterior model was upscaled from the Quasar Fire Carrier by Snickett. The...

It is designed for 45/70, 1.400 (35.5 mm) bullet length. It was designed for my printer so you may adjust the slicer if yours prints smaller or larger. The hole on the side is for small machine screw to attach the spring to. For ease of operation...

 Channel for cables is 1.5" wide by 0.75" high.  I use this to protect cables across a walkway, it was not designed to support a car driving over it, but feel free to try. ... I can't share the parametric model, but if you need a specific...

It is designed for .314, 1.000 (25.5 mm) bullet length. It was designed for my printer so you may adjust the slicer if yours prints smaller or larger. The hole on the side is for small machine screw to attach the spring to. For ease of operation sand...

The OG-9 Spider Droid wreaks havoc on Republic forces in X-Wing Ground Assault as a formidable asset for the Separatist faction.

The original X-end design has been modified for compatibility with the RichRaps Quick-Fit X Carriage (http://www.thingiverse.com/thing:19590). To ensure proper alignment, the motor has been moved 7.5mm away, while the idler was also shifted to line...

I then modeled a 4 1/4" x 4 1/4" tile with an opening for a 1/2" diameter pipe in SketchUp. I made the water spout solid in MeshMixer, subtracted from it a pipe running from the tile out the lion's mouth, mounted that to the tile, and cleaned up some...

Brass elbow fitting with 1/4" female NPT port and 1/4" male NPT boss.

Brass elbow fitting with 1/4" female NPT port and 1/4" male NPT boss.