1.25 telescope focuser 3d models
941490 3d models found related to 1.25 telescope focuser.thingiverse
Just a plain 31.8 mm plastic cap to avoid dust entering through the focuser of a telescope
thingiverse
A simple plug for a 1.25 focuser. ...The beveled edge makes it easy to insert and the fingerhold makes it easy to remove.
thingiverse
It's the same dimensions as a 1.25" eyepiece, so slides right into the focuser. The perforated plug is to be printed in flexible plastic for a friction fit. I get about 1.5 to 2% shrinkage with the flex I am using (Ninjaflex TPU), so the plug is...
thingiverse
This is a dust cover insert for telescopes with a 1.25" focuser. I've provided two STL files. One file has the standard dimensions. The other has been scaled up 1% to account for shrinkage with ABS. I printed my covers with the brim of the cap...
thingiverse
A quick easy to print dust cap for 1.25" accessories to keep dust out of your telescope
thingiverse
In the mean time, enjoy the printer live-cam at http://up.no-ip.org:8888 untill my site is back up :-) ) Instructions UPDATE 2016: Check out http://www.thingiverse.com/thing:1732234 UPDATE NOTE 4.JULY 2012: 2- Future ideas: Ad a tube at the base of...
prusaprinters
I needed a way to attach the Canon EOS 60d to my 1.25inch telescope focuser so i made this thing in onshapeThis is just a prototype version, if i make any improvements i will update the file.
thingiverse
This is a holder to allow prime focus photography with a Raspberry Pi Camera v2 in a 1.25" telescope focuser. I printed it with carbon fiber PLA with the tube section facing down and supports turned on. The slight roughness remaining from the...
thingiverse
I have cleaned up the SKP file. ...Now prints without trouble (tested on Cura 17.09).
thingiverse
**Parts to print:** * 1x focuser_gear * 2x knob * 1x focuser_housing_splitted_bottom * 1x tube_geared * 1x telescope_body_linear_focuser * 1x telescope_endCap **Parts to buy:** * 1x 75mm lens * 1x Telescope 1.25" ocular * 4x SelfTapping Screws /...
thingiverse
This is a 1.25" replacement for 0.965" focusers on 70mm Newtonian telescopes. I have continued to use the shaft with the gear and its cover. The shaft has a diameter of 5mm. The holes for the screws are at the same place, so you can exchange the...
thingiverse
Focus mask that can be fitted into the Dwarf 2 filter holder
thingiverse
Had a cheap 10" dobsonian telescope that needed a new eye piece focuser, so decided to create a 1.25 to 2" rack and pinion design. I printed out the parts using ABS and had to use a lot of sanding to make it as snug as possible to prevent slippage. I...
cults3d
Had a cheap 10" dobsonian telescope that needed a new eye piece focuser, so decided to create a 1.25 to 2" rack and pinion design. I printed out the parts using ABS and had to use a lot of sanding to make it as snug as possible to prevent slippage. I...
thingiverse
This adapter allows to attach any board CCTV camera module which has standard mounting drill pattern for M12 lens holder (2x D=2mm drill holes with 20 mm spacing) to a 1.25" telescope focuser. I already had Aptina MI5100 sensor board which I...
thingiverse
A micro 4/3 to 1.25" adapter for attaching a camera to a 1.25" telescope eyepiece focus assembly. Based on https://www.thingiverse.com/thing:4161613 by simzie, modified for 1.25" use. ...Fits camera and telescope, not yet used for imaging.
thingiverse
1.25 inch focuser for Dobsonian. It can be mounted flat or tubular. Focus stroke is 30 mm. The mounting screw hole is 4 mm. Eyepieces can not be screwed. 2017/02/23 The new model made it a mechanism to reduce looseness of the eyepiece. ...Print Settings...
thingiverse
Focuser 1,25 inch for telescope. ...Print Settings Printer: prusa i3 Resolution: 0,2mm ...
thingiverse
ABSFCS-1.25" Crayford focuser... The version .. ...0.1b will be upgraded 624zz bearing 6 bolts M4 25mm 4 bolts M3 30mm 4 nuts M3 4 bolt M4 70+mm 1
thingiverse
4 624zz bearing 2 MR105zz bearing 4 M3x16 screew (or 4x25 using springs) 4 M4x12 or 16 screew (i used 12mm stud) 1 M5x80 (or 90) threaded rod 2 M3 stud 6 M3 nut 2 M5 nut 1 1 1/4 (1/8 thickness) aluminum pipe Edited #1 The previous knob was oversized....
thingiverse
This is a small 1.25" helical focuser for a Newtonian telescope. ...The helical barrel is dimensioned to be a bit loose, so there is a setscrew hole in the side of the base that must be tapped for an M8 screw, and an M8 nylon bolt screwed in to provide...
thingiverse
1.25'' eyepiece focuser for DIY telescope. Editable FreeCad model included. ... For my telescope control software visit https://github.com/ZliRobot/RedShift
thingiverse
Here are a few collimation tutorials: https://garyseronik.com/a-beginners-guide-to-collimation/ https://www.skyandtelescope.com/astronomy-resources/how-to-align-your-newtonian-reflector-telescope/...
thingiverse
# Telscope Adapter 2 inch to 1,25 inch For usage with my 2 inch barlow on my 1,25 inch telescope focuser ;-) Something you would not get very easy to buy. # Print Rotate, so the 2 inch side is on the bottom. I used a little bit of sandpaper to...
thingiverse
v1.0.1 (2021-10-26) Simple, cheap,yet effective crayford focuser. Created in consideration that it will be 3d printed, so all models are optimised for this process. Parts used: • shrink tube (7 mm in shrinked state) • 623ZZ bearings x4 ...
thingiverse
1. m4 Hexagon Nut : 15 2. m4 x 20mm Hex SocketHead Cap Screw : 8 3. m4 x 10mm Hex SocketHead Cap Screw : 3 4. m4 x 15mm Hex SocketHead Cap Screw : 3 5. m2.5 x 4mm Flat Head Screw : 6 6. m3 x 3mm Socket set Screw : 2 7. m4 x 4mm Socket set Screw...
thingiverse
1.25 inch telescope eyepiece dust cover. ...Fits snugly (tested on Meade ETX-70)
thingiverse
V1.0 6/21/2020 This will hold 7 1.25" filters for telescopes
thingiverse
... this. Update: I printed and tested, on my Meade refracting telescope. a Lens needs to be added to make this work. I will post an update when I figure out how to make this work correctly. This may work on non-refracting telescopes. ...I'm not sure.