1.25 to 1.5 pool hose adapter 3d models

This is an above ground pool hose adapter that allows you to connect a 1.5 to 1.25 inch inside diameter size hose. Simply attach the clamps and use Teflon tape or pressure tape to ensure a secure seal. ... Print Settings: Printer: i3 Rafts: Not Required...

Just a litte adapter to go from a 1.25 currugated pool hose to a 3/4-11.5 garden hose. Did this so I can use the pool pump to empty out the pool. ...Also see my 1.25 hose adapter to taper on the inlet of the pool hose.

I attached a straightforward little adapter to connect a 1.25-inch hose directly to the pump supply line of my pool, giving me the ability to use this hose to suck up sand and small debris from the bottom with ease. ...This setup works perfectly with my...

This quick little adapter was designed to adapt a 1¼" pool hose to fit a 1½" connector on a pool filter's Waste port. Although it's not built for high pressure, you can use it on the intake side of a pool pump, but I wouldn't recommend using it on...

This quick adapter was designed to convert a 1¼" pool hose into a fit for a 1½" connector on a pool filter's waste port. It isn't built for high pressure, so while you can use it on the intake side of a pool pump, I would not recommend using it on...

I drew up a makeshift adapter to fit a 1¼" pool hose onto a 1½" connector on a pool filter's waste port. This quick fix isn't designed for high pressure, so while you can use it on the intake side of a pool pump, I wouldn't recommend using it on the...

... 1.5 inch ports. I'm adapting this to a 1.25 inch vacuum hose, CRAFTSMAN CMXZVBE38662 to be specific. ... Hopefully this helps anyone that ran into this problem as there seems to be no standard with vacuum hose sizes and readily available adapters.

This adapter enables connecting a substantial Intex 1.5" hose to a compact Intex 1.25" hose. The larger end demands an Intex gasket and the smaller end requires an O-ring. The smaller end has somewhat limited geometry, but applying some teflon tape...

To modify the 2.5-inch dust port on my Hitachi table saw, I had to accommodate the 1.25-inch hose from my mini ShopVac since the correct adapter wasn't available. ...Here's the solution.\r\n\r\nThis adapter fits snugly within the 2.5-inch port -...

LargeEndMeasured: Inside LargeEndDiameter: 42mm LargeEndLength: 33mm SmallEndMeasured: Outside SmallEndDiameter: 35mm SmallEndLength: 40mm TaperLength: 20mm WallThickness: 1.4mm

So to permit 1.5" hose to old 1.25" tool kit I created these adapters. Includes one straight adapter, one 30 degree angled adapter, and one 1-1/4 inch mini knife attachment for use in cleaning up shop bench top. Fusion 360, STL, and gcode files...

I designed this adapter connect the Intex **_Pool Drain Connector (part no. ...10184)_** to a **_1.5 inch Universal Vacuum Hose_** The adapter has female 1 1/16 garden hose thread and male 1.5 "threaded" insert for the 1.5" vacuum Hose. ...

The design accommodates an optional connection of a 1.25 inch pool hose to a standard garden hose. ...The user prints the O-ring component with TPU material properties.

A simple adapter to connect two 32mm / 1.25" pool hoses.That's it that's all..

This adapter fits between the hose for the pump and the hose for the heater. Tapered sides so that it didn't have to be perfect. *UPDATE: I wasn't happy with the original, the taper wasn't gradual enough to help and interfered with clamping. ...I've...

I design an adapter to allow the 1.25 hose to connect to the filter intake in the pool. Update: Added v2, increase size to fit better. Intex Compatible hose 1.25" https://amzn.to/2AtusPw Print instructionsUnassociated tags: intex pool Category:...

To make this process more efficient, I created an adapter that connects the 1.25 hose directly to the filter intake in my pool. Update: I've updated the design to version 2, increasing its size for better fitment. ... You can purchase a compatible 1.25...

... the bottom of it. ...To accomplish this task, I fashioned an adapter that enables me to connect a 1.25-inch hose directly to the filter intake in the pool. ... Update: I've upgraded the design to version 2, enlarging it slightly for a more secure fit.

When a coupler to connect two 1¼" pool hoses together is needed for a weekend getaway in the countryside and all local hardware stores are closed, it's time to print one. This small print job takes approximately an hour with a layer height of 0.3mm...

When a crucial coupler is needed to link two 1¼" pool hoses together on a weekend getaway in the countryside and every hardware store is inaccessible, you simply print one. This speedy little print only takes around an hour with a 0.3mm layer height...

When you need a coupler to connect two 1¼" pool hoses on a weekend getaway, and every hardware store is closed for the day, you just print one. This quick little print takes about an hour with a 0.3mm layer height and a 60mm/sec print speed. ...The fit...

When you need a coupler to connect two 1¼" pool hoses together on a weekend out in the sticks and every hardware store is closed.... you print one :) This quick little print only takes about an hour with a 0.3mm layer height and a 60mm/sec print...

No barbs on the hose half didn't cause any issues.Modeled with a flat bottom so you don't need to deal with supports or bad overhangs. If you print it with the flat side down, as intended, the threads still come out nice and there's no need for...

Many workshop tools have a 2.25 inch vacuum hose adapter and most vacuum have 1.25 inch hoses. This has a large 2.25 outside diameter that will fit into a 2.25 inch hole as on the Wen Sander. The inside small hole is for a 1.25 inch hose on the shop...

This is for the 1.5 Inch pool hose. I needed one and I thought some may need it as well. Both Ends are long enough to reach and create a seal with your hoses. ...but to prevent dripping you can buy the L shaped gaskets to add them for a better seal...

Customized version of https://www.thingiverse.com/thing:2945382 Created with Customizer! https://www.thingiverse.com/apps/customizer/run?thing_id=2945382 This is a work in progress, I'll update when I can verify that it works! ...

The adapter fits tightly onto the 1 1/4 inch hose of the ShopVac. It can be easily removed after use. ...This makes it ideal for attaching to a Wen 6515ST belt sander.

This is an adapter for use with a standard pool vacuum hose and a 1" Schedule 40 PVC Pipe. The pool vacuum hose connectors are not standard plumbing fitting sizes, and my non-standard setup requires some... adapting. Just insert a 1" pipe into the...

I wasn't able to find a suitable replacement adapter for the Ridgid floor attachment specifically so I was able create one based on the original. ...No scaling required, supports are required.

A common pool adapter, compatible with 1.5-inch hose connections, is available for purchase. The ends of this adapter taper from a diameter of 1.43 inches to 1.55 inches. Instead of buying a new one when yours breaks, simply print it out! If your...