1.5 pool hose 3d models

I had to connect two lengths of 1.25-inch vacuum hose to link my ShopVac to the dust shoe on my MPCNC, so I designed a coupler. ...The design was created using OpenSCAD, allowing anyone to modify it to accommodate different hose sizes as needed.

I was searching for a Y Fitting to Splitt 1 Hose in 4. After Days without success i decided to Remix another one. ... measurement 37% Scaling: Outher Diameter: 6.8mm Inner Diameter: 4.4mm flange Length: 19mm Fitts for 8mm Silicone Hose

Two holes at the top accommodate 1 1/4" screws for secure attachment and the holes along the side are designed for zip ties to hold down the hose firmly. ... This design was created using Tinkercad and can be edited online at...

Small water hose clip I use in my green hose to hold the hose with 3m adhesive.,

I gues you can also insert a sponge into the filter to filter the water even better. In my case the filter fitted very snugly into the hose so I didn't bother fixing it in place with a hose clamp.Next to the 1" model I also made a 1,25" model.I...

This fixture holds a 1/4-inch OD hose on the side of a rimless tank, specifically in the sump or refugium area. The gap is 5mm, allowing it to fit over a wide range of thicknesses from 1/4 inch to 3/4 inch. ...I utilized this setup for the rigid line of...

This is designed to hold a 1/4" OD simi-rigid hose t0 the side of a rimless tank ie the sump/refugium. ...the gap is 5mm so it will slide over a wide range of thicknesses from 1/4" to 3/4".I used it for the inlet line of my automatic water change...

I built a replica of the Ghostbusters leg hose connector, using exact measurements from the original movie costume, found on this webpage:http://www.gbfans.com/forum/viewtopic.php?t=30602&sid=413c87483872c205c927423f32a5cefa This custom part will...

... designed it myself and printed it. Its done with a resin printer because of the fine details. The original is a 16m long C-type fire hose with both ends a storz connector. ...I have also done some modifications, so not even 2 of this are identical.

I designed a custom pump fitting that perfectly fits a standard 1-inch hose. I used PLA material to print mine, and it's been working flawlessly. To achieve optimal results, make sure to orient the thread upwards during printing and use "Touching...

I created my own assortment of 1/2-inch inner diameter soaker hose fittings since they weren't available online. The collection includes a tee fitting, an elbow fitting, a cap, and a coupler. ...I've also added a Y connector to the mix.

1 Inch Hose T-Connector Print Settings Supports: Yes Resolution: 0,2mmInfill: 100% Filament: n/a PETG Category: Outdoor & Garden

Nothing fancy but this is the short tubing that fit into the hose (1.25 inch) at the end (opposite side of the vac) Diameter is 32mm at the base and a bit smaller at the top so you can plug your standard attachments

A hose connector measuring 1.5 inches in diameter and shaped as a hexagon is available for use. This connector features male threads to ensure secure attachment to hoses. ...With its hexagonal design, it provides a firm connection while being easy to...

Water hose adapter with a 1/2" thread Print instructionsLicence: Creative Commons - Attribution Category: Parts Print Settings Printer Brand: Prusa Printer: i3 MK2S Rafts: No Supports: No Resolution: 0.1 Infill: 50%

There are various 1-1/4 inch (1.25") and 1.5 inch vacuum hose adapters that can be used to connect a variety of vacuum hoses and attachments. I printed these because I could not find them sold anywhere. I printed mine vertically at .2mm height,...

Vakuum hose dapter 37,5 to 43mm

hose connector 1.25 inch to 1.0 inch 25,5mm to 32mm

Connected to a 1/2 inch water hose, a slightly larger amount of water drips with it exactly on a point over which I have attached it. Since support structures for objects like these can always be a bit annoying, I have developed a special...

These are a 3D printable hose clamps for tubes with 9mm outer diameter. Holes for the screws are 4mm wide. ...And the clamp it self is 10mm tall.

These are a 3D printable hose clamps for tubes with 9mm outer diameter. Holes for the screws are 4mm wide. ...And the clamp it self is 10mm tall.

I'm giving a hose adapter a go for the first time, but it's not yet proven to function properly.

A sizable model of a hose clamp. All parts are virtual to the assembly. Change the "Diameter" sketch to whatever size is needed. ...

Dewalt DWE6423 Sander Hose adapter to hook up to my 2.5" hose from my dust extractor.Sander side inner diameter is 43.2mmHose side outer diameter 61.9 tapered to 62.1 for a snug fit.Walls are 1.2mm thick (3x layers with .4 nozzle)

Dewalt DWE6423 Sander Hose adapter to hook up to my 2.5" hose from my dust extractor. Sander side inner diameter is 43.2mm Hose side outer diameter 61.9 tapered to 62.1 for a snug fit. ... Walls are 1.2mm thick (3x layers with .4 nozzle)

Quick Garden Hose Connection for Quarter Inch Faucet Printer Settings Printer Brand: Prusa Printed On: Prusa Clone Raft Requirements: Not Applicable Support Type: Yes Resolution: Low, 0.2 mm Infill Density: Moderate, 30%

Standard 1/2 inch to 1 inch Hose Clamp. ...Printed with Impact Resistant Acrylonitrile-Butadiene-Styrene for high temperature applications.

Assorted set of resin made hose joints for detailing your 1/20 and 1/24 scale models.

Need a splitter, for my ShopVac 1-1/4" hose, but could not find one... ...so I designed one.

Individual utilizes 0.5" to 0.25" hose clamp printed utilizing ABS material during high temperature conditions.